Refer to DTC P0031 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2195
P2197 |
Conditions (a) and (b) continue for 40 seconds or more
(2 trip detection logic): (a) Air fuel ratio sensor voltage is higher than 3.8 V. (b) Heated oxygen sensor voltage is 0.15 V or higher. |
·
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
Intake system ·
Fuel pressure ·
Fuel injector assembly ·
ECM |
| While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic). | ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
|
| P2196
P2198 |
Conditions (a) and (b) continue for 40 seconds or more
(2 trip detection logic): (a) Air fuel ratio sensor voltage is less than 2.8 V. (b) Heated oxygen sensor voltage is less than 0.6 V. |
·
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
Intake system ·
Fuel pressure ·
Fuel injector assembly ·
ECM |
| While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.8 mA for 3 seconds (2 trip detection logic). | ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
DTCs P2195 and P2196 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
DTCs P2197 and P2198 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / All Data / AFS Voltage B1S1 or AFS Voltage B2S1.
Short-term fuel trim values can also be read using the intelligent tester.
The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the intelligent tester.
If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
On the tester, enter the following menus to check the fuel-cut status: Powertrain / Engine / Data List / All Data / Idle Fuel Cut.
Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
With the shift lever in S [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].
Fuel-cut is performed when the following conditions are met:
Accelerator pedal is fully released.
Fuel injection returns at 1500 rpm.
Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
Repeat steps [C] through [E] above at least 3 times in one driving cycle.
Enter the following menus: Powertrain / Engine / DTC [F].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2195, P2196, P2197 or P2198 is output | A |
| DTC P2195, P2196, P2197 or P2198 and P0136, P0137, P0138, P0156, P0157 or P0158 are output | A |
| DTC P2195, P2196, P2197 or P2198 and other DTCs are output | B |
If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.
A
B
Has the vehicle run out of fuel in the past?
YES
NO
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Data List / All Data / AFS Current B1S1 or AFS Current B2S1.
Check the test value of the air fuel ratio sensor output current during fuel-cut.
| Test Value | Proceed to |
|---|---|
| Within normal range (0.8 mA or higher, and less than 2.2 mA) | A |
| Outside normal range (Less than 0.8 mA, or 2.2 mA or higher) | B |
A
B
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| Tester Display
(Sensor) |
Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1
AFS Voltage B2S1 (Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2
O2S B2S2 (Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
|---|---|---|---|
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Lean/Rich | Lean/Rich | Normal | B |
Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltages (AFS Voltage B1S1 and AFS Voltage B2S1) are consistently higher than 3.4 V, and the heated oxygen sensor output voltages (O2S B1S2 and O2S B2S2) are consistently below 0.4 V.
Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 and AFS Voltage B2S1 are consistently below 3.1 V, and the O2S B1S2 and O2S B2S2 are consistently higher than 0.55 V.
Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.
Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).
A
B
Check the intake system for vacuum leaks.
No leaks in the intake system.
OK
NG
Check for exhaust gas leaks.
No gas leaks.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injector pattern is poor) (See page Engine / Hybrid System>2GR-FE FUEL>FUEL INJECTOR>INSPECTION).
OK
NG
Replace the air fuel ratio sensor (See page Engine / Hybrid System>2GR-FE EMISSION CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | A |
| NORMAL (DTC is not output) | B |
A
B
Replace the ECM (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>ECM>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
NEXT
Replace the air fuel ratio sensor (See page Engine / Hybrid System>2GR-FE EMISSION CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | B |
A
B
Check the fuel lines for leaks or blockage.
OK
NG