Refer to DTC P0031 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2237
P2240 |
An open in the circuit between terminals A1A+ (A2A+) and A1A- (A2A-) of the air fuel ratio sensor while the engine is running (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
| P2238
P2241 |
·
Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at terminal A1A+ (A2A+) is 0.5 V or less (b) Voltage difference between terminals A1A+ (A2A+) and A1A- (A2A-) is 0.1 V or less ·
Case 2: Air fuel ratio sensor admittance is less than 0.0074 1/Ω (2 trip detection logic). |
·
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
| P2239
P2242 |
The A1A+ (A2A+) voltage is higher than 4.5 V (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
| P2252
P2255 |
The A1A- (A2A-) voltage is 0.5 V or less (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
| P2253
P2256 |
The A1A- (A2A-) voltage is higher than 4.5 V (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
Refer to DTC P2195 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2195).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Refer to "Data List / Active Test" [AFS Voltage B1S1 and AFS Voltage B2S1] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D42-1 (HA1A) - D1-86 (HA1A) | Always | Below 1 Ω |
| D42-3 (A1A+) - D1-93 (A1A+) | Always | Below 1 Ω |
| D42-4 (A1A-) - D1-116 (A1A-) | Always | Below 1 Ω |
| D8-1 (HA2A) - D1-109 (HA2A) | Always | Below 1 Ω |
| D8-3 (A2A+) - D1-120 (A2A+) | Always | Below 1 Ω |
| D8-4 (A2A-) - D1-119 (A2A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D42-1 (HA1A) or D1-86 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D42-3 (A1A+) or D1-93 (A1A+) - Body ground | Always | 10 kΩ or higher |
| D42-4 (A1A-) or D1-116 (A1A-) - Body ground | Always | 10 kΩ or higher |
| D8-1 (HA2A) or D1-109 (HA2A) - Body ground | Always | 10 kΩ or higher |
| D8-3 (A2A+) or D1-120 (A2A+) - Body ground | Always | 10 kΩ or higher |
| D8-4 (A2A-) or D1-119 (A2A-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the air fuel ratio sensor (See page Engine / Hybrid System>2GR-FE EMISSION CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Start the engine and wait for 5 minutes or more.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL (DTC is not output) | A |
| ABNORMAL
(DTC P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output) |
B |
A
B