Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)  P2241  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)  P2242  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  P2255  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)  P2256  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)  


DESCRIPTION

Refer to DTC P0031 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031).

DTC No. DTC Detection Condition Trouble Area
P2237
P2240
An open in the circuit between terminals A1A+ (A2A+) and A1A- (A2A-) of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2238
P2241
·

Case 1:


Condition (a) or (b) continues for 5.0 seconds or more
(2 trip detection logic):
(a) Voltage at terminal A1A+ (A2A+) is 0.5 V or less
(b) Voltage difference between terminals A1A+ (A2A+) and A1A- (A2A-) is 0.1 V or less
·

Case 2:


Air fuel ratio sensor admittance is less than 0.0074 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2239
P2242
The A1A+ (A2A+) voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2252
P2255
The A1A- (A2A-) voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2253
P2256
The A1A- (A2A-) voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM



HINT:
·

DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

·

DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Refer to "Data List / Active Test" [AFS Voltage B1S1 and AFS Voltage B2S1] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D42-1 (HA1A) - D1-86 (HA1A) Always Below 1 Ω
D42-3 (A1A+) - D1-93 (A1A+) Always Below 1 Ω
D42-4 (A1A-) - D1-116 (A1A-) Always Below 1 Ω
D8-1 (HA2A) - D1-109 (HA2A) Always Below 1 Ω
D8-3 (A2A+) - D1-120 (A2A+) Always Below 1 Ω
D8-4 (A2A-) - D1-119 (A2A-) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D42-1 (HA1A) or D1-86 (HA1A) - Body ground Always 10 kΩ or higher
D42-3 (A1A+) or D1-93 (A1A+) - Body ground Always 10 kΩ or higher
D42-4 (A1A-) or D1-116 (A1A-) - Body ground Always 10 kΩ or higher
D8-1 (HA2A) or D1-109 (HA2A) - Body ground Always 10 kΩ or higher
D8-3 (A2A+) or D1-120 (A2A+) - Body ground Always 10 kΩ or higher
D8-4 (A2A-) or D1-119 (A2A-) - Body ground Always 10 kΩ or higher




OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and turn the tester on.


g.

Start the engine and wait for 5 minutes or more.


h.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


i.

Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.


j.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL
(DTC P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output)
B



A

END

B