Refer to DTC P0013 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0013).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0014
P0024 |
Advanced cam timing:
With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (2 trip detection logic): (1) Difference between target and actual exhaust valve timing is more than 5°CA (Crankshaft Angle) for 4.5 seconds (2) Current exhaust valve timing is fixed (timing changes less than 5°CA in 5 seconds) (3) Variations in VVT controller timing are more than 19°CA of maximum delayed timing (advanced) |
·
Valve timing ·
Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1, 2) ·
Oil control valve filter (RH, LH) ·
Oil pipe ·
Camshaft timing exhaust gear assembly (bank 1, 2) ·
ECM |
| P0015
P0025 |
Retarded cam timing:
With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (1 trip detection logic): (1) Difference between target and actual exhaust valve timing is more than 5°CA (Crankshaft Angle) for 4.5 seconds (2) Current exhaust valve timing is fixed (timing changes less than 5°CA in 5 seconds) (3) Variations in VVT controller timing are 19°CA or less of maximum delayed timing (retarded) |
Refer to DTC P0013 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0013).
| Abnormal bank | Advanced timing over
(Valve timing is out of specified range) |
Retarded timing over
(Valve timing is out of specified range) |
|---|---|---|
| Bank 1 | P0014 | P0015 |
| Bank 2 | P0024 | P0025 |
If DTC P0014 or P0015 is output, check the VVT system (for exhaust camshaft of bank 1) circuit.
If DTC P0024 or P0025 is output, check the VVT system (for exhaust camshaft of bank 2) circuit.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
DTC P0014, P0015, P0024 or P0025 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0014, P0015, P0024 or P0025 is output | A |
| DTC P0014, P0015, P0024 or P0025 and other DTCs are output | B |
If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.
A
B
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the tester.
| Tester Operation | Engine Condition |
|---|---|
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
Refer to "Data List / Active Test" [VVT Ex OCV Duty #1, VVT Ex Chg Angle #1, VVT Ex OCV Duty #2 and VVT Ex Chg Angle #2] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle for more than 10 minutes.
Enter the following menus: Powertrain / Engine / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0014, P0015, P0024 or P0025 is output | B |
DTC P0014, P0015, P0024 or P0025 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.
A
B
OK
NG
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).
OK
NG
OK
NG
Replace the camshaft timing exhaust gear assembly (bank 1 or bank 2) (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Drive the vehicle for more than 10 minutes.
Enter the following menus: Powertrain / Engine / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0014, P0015, P0024 or P0025 is output | B |
A
B