Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  


DESCRIPTION

The Camshaft Position (CMP) sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed onto the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft timing rotor passes through the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No. DTC Detection Condition Trouble Area
P0340 When one of the following conditions is met:
·

A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).

·

No camshaft position sensor signal to the ECM at an engine speed of 600 rpm or higher (1 trip detection logic).

·

No camshaft position sensor signal to the ECM while cranking (2 trip detection logic).


·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Intake camshaft

·

Valve timing

·

ECM



HINT:

DTC P0340 indicates a malfunction relating to the CMP sensor (+) circuit (the wire harness between the ECM and CMP sensor, and the CMP sensor itself).


Reference: Inspection using an oscilloscope (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
a.


OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the CMP sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D55-1 - D2-99 (G2+) Always Below 1 Ω
D55-2 - D2-98 (G2-)


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D55-1 or D2-99 (G2+) - Body ground Always 10 kΩ or higher
D55-2 or D2-98 (G2-) - Body ground




OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.
B319222E12
1.708,1.563 2.375,1.792 0.667,0.229 10 false Clearance 0.542,1.729 1.354,1.969 0.813,0.24 10 false Normal 2.438,1.802 3.115,2.094 0.677,0.292 10 false Abnormal

Check the CMP sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

NG

SECURELY REINSTALL SENSOR

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

OK

5.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

5.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Inspect the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.




OK

6.REPLACE CAMSHAFT POSITION SENSOR

NG

6.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0340 A
No output B



HINT:

If the engine does not start, replace the ECM.



A

B

END