Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › TIMING CHAIN › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291833 TIMING CHAIN A

2AZ-FE ENGINE MECHANICAL  TIMING CHAIN  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Check whether the engine is TMC made or not by referring to the following illustration.

U188506E01
3.93,0.096 4.173,0.285 0.243,0.189 10 *B 0.339,0.096 0.588,0.285 0.249,0.189 10 *A 2.471,0.822 2.640,0.977 0.169,0.154 10 *1 2.471,0.932 2.045,1.143 false 6.069,0.84 6.239,0.994 0.169,0.154 10 *1 6.069,0.964 5.767,1.216 false 4.061,1.835 4.230,1.989 0.169,0.154 10 *2 6.342,1.937 6.511,2.092 0.169,0.154 10 *3 4.233,1.894 4.774,1.749 false 6.33,2.025 5.924,2.109 false

Text in Illustration
*A for TMC Made Engine *B except TMC Made Engine
*1 Engine Oil Level Dipstick Guide *2 Water Inlet Housing
*3 Water Inlet Housing Drain Cock Assembly - -


PROCEDURE

Hide 13507 1.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.
B011424

Set the crankshaft key in the left horizontal position.


b.

Turn the cutout of the drive shaft so that it faces upward.


c.
A094198E15
1.479,3.104 0.917,2.854 true 1.521,2.438 1.156,1.688 true 2.604,1.469 1.948,0.969 false 1.635,3.01 2.292,2.677 true 1.885,0.271 1.125,0.271 true 2.01,0.406 1.135,0.604 true 2.375,2.573 3.167,2.74 0.792,0.167 10 false Timing Mark 0.156,0.5 0.948,0.667 0.792,0.167 10 false Timing Mark 0.094,2.75 0.75,2.917 0.656,0.167 10 false Mark Link 0.313,0.167 1.104,0.333 0.792,0.167 10 false Mark Link 0.021,1.521 1.01,2.031 0.99,0.51 10 false Oil Pump Drive Shaft Sprocket 2.292,1.51 3.229,1.854 0.938,0.344 10 true Oil Pump Drive Sprocket

Align the yellow mark links with the timing marks of each gear as shown in the illustration.


d.

Install the sprockets onto the crankshaft and oil pump shaft with the chain wrapped on the gears.


e.

Temporarily tighten the oil pump drive shaft sprocket with the nut.


f.
U188234E02
2.479,1.344 2.479,2.406 true 1.938,1.646 1.938,3 true 2.323,2.438 2.802,2.635 0.479,0.198 10 true Spring 2.552,0.844 2.948,1.104 0.396,0.26 10 true Bolt 1.188,3 2.833,3.281 1.646,0.281 10 true Chain Tensioner Plate

Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


g.
A098352E11
0.656,0.677 0.656,1.667 false 0.354,1.667 0.875,1.833 0.521,0.167 10 false Groove

Align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.


h.

Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)


Hide 13521 2.INSTALL CRANKSHAFT TIMING SPROCKET

A128186

Hide 13561 3.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A132570

Install the chain vibration damper with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 13506 4.INSTALL CHAIN SUB-ASSEMBLY

a.
A098367E06
0.906,2.656 2.354,3.083 2.354,3.083 2.719,2.167 true 0.844,2.115 2.354,3.083 true 0.729,0.458 2.115,1.031 2.115,1.031 2.625,0.396 true 1.896,3.083 2.917,3.396 1.021,0.313 10 true Timing Mark 1.667,1.031 2.542,1.208 0.875,0.177 10 false Timing Mark

Set the No. 1 cylinder to TDC/compression.

i.

Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.


ii.
A052505

Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.



b.
A094576E12
2.125,1.063 2.448,1.063 true 2.333,0.354 1.979,1.052 true 2.49,0.99 3.146,1.365 0.656,0.375 10 true Mark Link 2.375,0.281 3.177,0.646 0.802,0.365 10 true Timing Mark

Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.


c.
A098369E03
1.083,0.271 1.385,0.844 true 0.698,0.177 1.031,0.354 0.333,0.177 10 true SST

Using SST and a hammer, tap in the crankshaft timing sprocket.

SST
09309-37010  


d.
A098370E10
2.479,0.688 2.854,1.323 false 1.146,0.635 0.906,1.323 0.906,1.323 1.188,0.896 false 1.125,0.51 1.021,0.125 1.021,0.125 2.448,0.552 false 2.427,1.354 3.281,1.781 0.854,0.427 10 true Timing Mark 0.417,1.354 1.25,1.781 0.833,0.427 10 true Timing Mark 0.188,0.042 0.833,0.198 0.646,0.156 10 false Mark Link

Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.


Hide 13559 5.INSTALL CHAIN TENSIONER SLIPPER

a.
A124787E01
0.581,0.147 0.928,0.310 0.347,0.163 10 Hold

Install the chain tensioner slipper with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 13566B 6.INSTALL TIMING CHAIN GUIDE

a.
A077243

Install the timing chain guide with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 19315 7.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A124770

Install the sensor plate with the "F" mark facing forward.


Hide 11302 8.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.


b.
A094577E10
0.833,1.271 1.573,1.771 1.573,1.771 2.385,1.271 true 1.458,1.802 1.719,1.99 0.26,0.188 10 true *1

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4.0 to 4.5 mm (0.157 to 0.177 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the chain cover within 3 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installing the chain cover.




c.

Apply a continuous bead of seal packing as shown in the illustration.

A395584E01
1.198,1.292 0.51,0.604 false 0.51,0.604 0.906,0.604 false 1.885,1.708 2.344,0.677 false 2.344,0.677 2.698,0.677 false 6.323,0.563 6.146,0.365 6.146,0.365 6.021,0.365 false 6.396,1.271 6.135,1.646 6.135,1.646 6.135,1.802 false 4.667,1.896 4.802,1.896 4.802,1.896 4.833,1.552 false 5.344,2.01 5.344,1.792 5.344,1.792 5.063,1.292 false 1.427,3.073 1.792,3.073 false 2.323,3.708 2.323,3.552 2.323,3.552 2.552,3.406 false 3.25,4.677 3.813,4.677 false 4.75,5.781 4.75,5.323 4.75,5.323 5.219,4.969 false 6.208,5.792 6.208,5.281 6.208,5.281 6.604,4.906 false 0.969,0.531 1.573,0.729 0.604,0.198 10 false 4.0 mm 2.75,0.594 3.344,0.792 0.594,0.198 10 false 4.0 mm 4.125,1.823 4.688,2.01 0.563,0.188 10 false 2.5 mm 4.958,2.083 5.865,2.281 0.906,0.198 10 false 2.5 to 3.0 mm 5.917,1.833 6.469,2.031 0.552,0.198 10 false 4.0 mm 5.094,0.271 6.021,0.469 0.927,0.198 10 false 4.0 to 4.5 mm 4.75,0.125 4.906,0.323 0.156,0.198 10 false D 6.25,0.104 6.406,0.302 0.156,0.198 10 false E 0.583,1.49 0.74,1.688 0.156,0.198 10 false A 0.563,2.104 0.719,2.302 0.156,0.198 10 false B 0.594,3.958 0.75,4.156 0.156,0.198 10 false C 0.938,2.979 1.469,3.177 0.531,0.198 10 false 3.0 mm 1.958,3.75 2.854,4.115 0.896,0.365 10 true 2.5 to 3.0 mm 1.458,1.271 1.615,1.469 0.156,0.198 10 false H 2.156,3.01 2.313,3.208 0.156,0.198 10 false I 3.823,1.448 3.979,1.646 0.156,0.198 10 false D 3.823,1.979 3.979,2.177 0.156,0.198 10 false E 3.823,2.281 3.979,2.479 0.156,0.198 10 false F 3.833,3.979 3.99,4.177 0.156,0.198 10 false G 3.875,4.594 4.854,4.771 0.979,0.177 10 false 2.5 to 3.0 mm 4.865,3.49 5.563,3.667 0.698,0.177 10 false φ 17.5 mm 6.208,3.49 6.969,3.688 0.76,0.198 10 false φ 13.0 mm 5.188,2.406 5.344,2.604 0.156,0.198 10 false H 6.521,2.385 6.677,2.583 0.156,0.198 10 false I 5.115,4.063 5.271,4.26 0.156,0.198 10 false B 6.521,4.083 6.646,4.25 0.125,0.167 10 false F 4.417,5.854 5.333,6.063 0.917,0.208 10 false 5.5 to 6.0 mm 5.844,5.865 6.823,6.073 0.979,0.208 10 false 4.5 to 5.0 mm

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Area Seal Packing Diameter (Round) Distance from Edge of Cover to Edge of Seal Packing Diameter Measured from Center of Seal Packing
A 4.0 mm (0.157 in.) - -
B 5.5 to 6.0 mm (0.217 to 0.236 in.) - -
C 3.0 mm (0.118 in.) - -
D 2.5 to 3.0 mm (0.0984 to 0.118 in.) 2.5 mm (0.0984 in.) -
E 4.0 to 4.5 mm (0.157 to 0.177 in.) - -
F 4.5 to 5.0 mm (0.177 to 0.197 in.) - -
G 2.5 to 3.0 mm (0.0984 to 0.118 in.) - -
H 4.0 mm (0.157 in.) - 17.5 mm (0.689 in.)
I 2.5 to 3.0 mm (0.0984 to 0.118 in.) - 13.0 mm (0.512 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the chain cover within 3 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installing the chain cover.




d.

Apply adhesive to the threads of bolt A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A132568E19
0.219,0.5 0.438,0.667 0.219,0.167 10 false *1 2.979,0.146 3.156,0.323 0.177,0.177 10 false *1 1.406,1.604 1.615,1.813 0.208,0.208 10 true A 0.302,2.24 0.51,2.406 0.208,0.167 10 false B 0.198,2.625 0.406,2.792 0.208,0.167 10 false B 0.333,3.5 0.542,3.667 0.208,0.167 10 false B 0.594,4.292 0.802,4.458 0.208,0.167 10 false B 2.729,3.917 2.938,4.083 0.208,0.167 10 false B 2.813,3.323 3.021,3.49 0.208,0.167 10 false B 2.906,2.865 3.115,3.031 0.208,0.167 10 false B 2.625,2.24 2.833,2.406 0.208,0.167 10 false B 0.271,0.99 0.479,1.156 0.208,0.167 10 false C 0.313,1.521 0.521,1.688 0.208,0.167 10 false C 2.948,1.531 3.156,1.698 0.208,0.167 10 false C

Temporarily install the timing chain cover with the 12 bolts and 2 nuts.

Bolt length:
Item Specified Condition
Bolt A 30 mm (1.18 in.)
10 mm head
Bolt B 30 mm (1.18 in.)
12 mm head
Bolt C 40 mm (1.57 in.)
14 mm head


Text in Illustration
*1 Nut


f.
A128165

Temporarily install the engine mounting bracket with the 3 bolts.


g.

Tighten the 15 bolts and 2 nuts in the sequence shown in the illustration.

A188148E05
5.969,1.323 6.146,1.521 0.177,0.198 10 false 1 2.104,1.563 2.281,1.76 0.177,0.198 10 false A 2.948,1.323 3.125,1.521 0.177,0.198 10 false C 2.688,1.885 2.865,2.083 0.177,0.198 10 false B 3.073,0.896 3.25,1.094 0.177,0.198 10 false C 1.01,1.281 1.188,1.479 0.177,0.198 10 false C 0.969,0.906 1.146,1.104 0.177,0.198 10 false C 2.854,2.323 3.031,2.521 0.177,0.198 10 false B 2.885,2.615 3.063,2.813 0.177,0.198 10 false B 0.969,1.854 1.146,2.052 0.177,0.198 10 false B 0.969,2.177 1.146,2.375 0.177,0.198 10 false B 1.052,2.771 1.229,2.969 0.177,0.198 10 false B 1.521,3.542 1.698,3.74 0.177,0.198 10 false B 2.344,3.51 2.521,3.708 0.177,0.198 10 false B 1.771,0.844 1.948,1.042 0.177,0.198 10 false C 1.76,1.156 1.938,1.354 0.177,0.198 10 false C 3.104,0.521 3.479,0.719 0.375,0.198 10 false NUT 0.729,0.521 1.104,0.719 0.375,0.198 10 false NUT 4.052,1.281 4.229,1.479 0.177,0.198 10 false 2 4.813,0.833 4.99,1.031 0.177,0.198 10 false 3 4.021,0.906 4.198,1.104 0.177,0.198 10 false 4 6.094,0.906 6.271,1.104 0.177,0.198 10 false 5 4.823,1.135 5,1.333 0.177,0.198 10 false 6 4.031,1.854 4.208,2.052 0.177,0.198 10 false 7 4,2.167 4.177,2.365 0.177,0.198 10 false 9 5.708,1.896 5.885,2.094 0.177,0.198 10 false 8 5.875,2.313 6.115,2.51 0.24,0.198 10 false 10 5.813,2.656 6.052,2.854 0.24,0.198 10 false 12 4.51,3.542 4.75,3.74 0.24,0.198 10 false 13 4.031,2.781 4.271,2.979 0.24,0.198 10 false 11 5.323,3.521 5.563,3.719 0.24,0.198 10 false 14 6.115,0.51 6.354,0.708 0.24,0.198 10 false 16 5.094,1.583 5.333,1.781 0.24,0.198 10 false 15 3.906,0.521 4.146,0.719 0.24,0.198 10 false 17

Torque:
Bolt A : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Bolt B : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt C : 55 N*m (561 kgf*cm, 41 ft.*lbf)
Nut : 11 N*m (112 kgf*cm, 8 ft.*lbf)


h.
A014253

Using an E10 "TORX" socket, install the stud bolt for the V-ribbed belt tensioner.

Torque:
22 N*m (219 kgf*cm, 16 ft.*lbf)


Hide 13540 9.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A098376E16
1.25,1.323 1.25,1.729 false 0.896,1.5 0.771,1.833 false 0.135,1.083 0.521,1.271 0.385,0.188 10 false Push 0.333,0.604 0.74,0.792 0.406,0.188 10 false Raise 0.625,1.854 0.906,2.052 0.281,0.198 10 false Pin 1.031,1.719 1.417,1.896 0.385,0.177 10 false Hook

Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.


b.
A098377E10
2.438,2.521 2.438,2.813 false 1.958,2.833 2.813,3.01 0.854,0.177 10 false Engine Front

Install a new gasket and the chain tensioner with the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

When installing the chain tensioner, set the hook again if the hook releases the plunger.



Hide 16620 10.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A214461E03
1.229,0.281 1.365,0.438 0.135,0.156 10 true A 0.677,1.781 0.979,1.938 0.302,0.156 10 false Nut 0.49,0.865 0.917,1.021 0.427,0.156 10 false Bolt

Temporarily install the V-ribbed belt tensioner assembly with the nut.

NOTICE:

Do not lift the engine more than necessary.



b.

Slightly push down on the V-ribbed belt tensioner assembly at the part (A) to align the holes of the engine and tensioner as shown in the illustration, and temporarily install the bolt.


c.
A147820E01
0.786,1.138 1.016,1.284 0.230,0.146 10 Pin

Tighten the bolt and nut to install the V-ribbed belt tensioner.

Torque:
59.5 N*m (607 kgf*cm, 44 ft.*lbf)

NOTICE:
·

When replacing the V-ribbed belt tensioner with a new one, do not pull out the pin.

·

The pin will be removed in a later step.




Hide 16603B 11.INSTALL IDLER PULLEY BRACKET

a.
A114359

Install the idler pulley bracket with the 2 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 12361A 13.INSTALL FRONT ENGINE MOUNTING INSULATOR

Hide 12281A 14.REMOVE ENGINE HANGER

a.

Remove the chain block and sling device.


b.

Remove the No. 1 and No. 2 engine hangers.


Hide 13471 15.INSTALL CRANKSHAFT PULLEY

a.
A098346E07
1.51,0.698 0.552,0.698 0.552,0.698 1.438,0.875 false 0.146,0.604 0.469,0.771 0.323,0.167 10 false SST

Using SST, secure the pulley in place and tighten the bolt.

SST
09213-54015  (91651-60855)
09330-00021  

T = 180 N*m{ 1,835 kgf*cm 133 ft.*lbf }


b.
A112204E02
3.044,2.013 3.366,2.203 0.323,0.191 10 Turn 0.674,1.597 1.423,1.776 0.749,0.179 10 Disconnect 1.256,2.773 1.518,2.938 0.262,0.165 10 Pin 0.115,1.991 0.479,2.184 0.365,0.193 10 Hook 0.939,2.471 1.226,2.858 false 0.934,2.333 0.565,2.102 false

Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.


c.
A112205E02
2.469,2.621 2.814,2.796 0.345,0.175 10 Turn 0.488,2.718 0.883,2.893 0.395,0.175 10 Push 1.068,1.912 1.581,2.114 0.512,0.202 10 Plunger 1.006,2.352 0.957,1.995 0.957,1.995 1.03,1.995 false

Turn the crankshaft clockwise, then check that the plunger is extended.


Hide 12101 16.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.


b.
A114332E01
2.289,2.837 3.123,3.029 0.834,0.192 10 Seal Packing 0.477,3.43 1.732,3.660 1.256,0.230 10 6.0 mm (0.236 in.) 0.178,4.22 2.056,4.394 1.878,0.174 10 Seal Diameter: 3.0 to 4.0 mm 2.792,1.891 2.792,2.788 false

Apply a continuous bead of seal packing (Diameter: 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent


NOTICE:
·

Remove any oil from the contact surfaces.


·

Install the oil pan within 3 minutes of applying seal packing.


·

Do not add engine oil for at least 2 hours after installing the oil pan.




c.

Install the oil pan to the cylinder block.


d.
A114333E01
0.917,0.205 1.288,0.382 0.371,0.177 10 1, 15 2.238,0 2.443,0.163 0.205,0.163 10 10 2.493,0.147 2.697,0.310 0.205,0.163 10 11 2.88,0.278 3.084,0.441 0.205,0.163 10 12 3.055,1.037 3.259,1.200 0.205,0.163 10 13 2.874,1.778 3.079,1.940 0.205,0.163 10 14 1.599,0 1.769,0.163 0.170,0.163 10 9 0.664,0.389 0.834,0.551 0.170,0.163 10 8 0.374,0.876 0.544,1.039 0.170,0.163 10 7 0.374,1.34 0.544,1.503 0.170,0.163 10 6 0.633,1.838 0.803,2.000 0.170,0.163 10 5 0.899,1.96 1.068,2.123 0.170,0.163 10 4 1.992,1.973 2.162,2.136 0.170,0.163 10 3 2.371,1.916 2.541,2.079 0.170,0.163 10 2

Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 11301K 17.INSTALL CRANKSHAFT POSITION SENSOR (for TMC Made Engine)

a.
A095436E25
1.76,1.292 1.427,1.51 false 1.219,1.469 1.677,1.656 0.458,0.188 10 false *1

Apply a light coat of engine oil to the O-ring on the crank position sensor.

Text in Illustration
*1 O-ring


b.
A234730

Install the crank position sensor with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Do not twist the O-ring.



c.

Install the 2 wire harness clamps.


d.

Install the connector to the connector bracket.


Hide 11301K 18.INSTALL CRANKSHAFT POSITION SENSOR (except TMC Made Engine)

a.
A095436E25
1.76,1.292 1.427,1.51 false 1.219,1.469 1.677,1.656 0.458,0.188 10 false *1

Apply a light coat of engine oil to the O-ring on the crank position sensor.

Text in Illustration
*1 O-ring


b.
A234731

Install the crank position sensor with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Do not twist the O-ring.



c.

Install the wire harness clamp.


d.

Install the connector to the connector bracket.


Hide 11201 19.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove any old packing material from the contact surface.


b.
A094205

Apply seal packing to the 2 locations shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the oil pan within 3 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installing the oil pan.




c.
A094204E10
0.073,0.135 0.208,0.292 0.135,0.156 10 false A 0.115,1.771 0.25,1.927 0.135,0.156 10 false A 0.615,0.167 0.75,0.323 0.135,0.156 10 false A 1.625,0.219 1.76,0.375 0.135,0.156 10 false A 2.969,0.26 3.104,0.417 0.135,0.156 10 false A 1.896,1.729 2.031,1.885 0.135,0.156 10 false A 2.365,0.625 2.5,0.781 0.135,0.156 10 false B 1.188,0.625 1.323,0.781 0.135,0.156 10 true B 0.667,1.781 0.938,1.938 0.271,0.156 10 false Nut 2.792,1.698 3.063,1.854 0.271,0.156 10 false Nut

Install the cylinder head cover with the 8 bolts and 2 nuts.

Torque:
Bolt A : 11 N*m (112 kgf*cm, 8 ft.*lbf)
Bolt B : 14 N*m (143 kgf*cm, 10 ft.*lbf)
Nut : 11 N*m (112 kgf*cm, 8 ft.*lbf)


d.
A132558

Install the 2 engine wires with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.
A132557

Connect the 2 ventilation hoses to the cylinder head cover.


Hide 51217A 25.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 27.INSTALL COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

a.

Install the cowl top outer panel with windshield wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 30.CHECK FOR ENGINE OIL LEAKS

Hide 31.CHECK FOR EXHAUST GAS LEAKS

Hide 53701 32.INSTALL FRONT FENDER APRON RH

Hide 51441 33.INSTALL NO. 1 ENGINE UNDER COVER

Hide 34.INSTALL FRONT WHEEL RH

Hide 53292A 35.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 36.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.