Home › Engine / Hybrid System › 2AZ-FE COOLING › WATER PUMP › from 2016.05
RM24M0E _51 Engine / Hybrid System _059552 2AZ-FE COOLING _0291855 WATER PUMP A

2AZ-FE COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL WATER PUMP ASSEMBLY

a.

Remove any old seal packing material from the contact surfaces.


b.
A393966E01
1.531,0.344 2.01,0.635 true 2.427,0.885 2.74,1.083 0.313,0.198 10 false A 1.323,0.229 1.635,0.427 0.313,0.198 10 false *1 0.688,2.979 1.125,3.208 0.438,0.229 10 false A-A 1.771,3.167 3.073,3.625 1.302,0.458 10 false 0.5 to 1.0 mm (0.0197 to 0.0394 in.) 0.406,4.146 1.792,4.396 1.385,0.25 10 false 2.5 mm (0.0984 in.) 3.115,0.917 3.427,1.115 0.313,0.198 10 false A

Apply a continuous line of seal packing as shown in the illustration.

Text in Illustration
*1 Seal Packing

Seal packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Standard seal diameter:

2.2 to 2.5 mm (0.0866 to 0.0984 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

The parts must be set within 3 minutes of applying seal packing. Otherwise, the material must be removed and reapplied.




c.
U188545E02
1.958,0.719 2.281,0.542 2.281,0.542 2.396,0.542 false 2.427,0.448 2.615,0.625 0.188,0.177 10 false *1 2.5,0.844 2.635,1.021 0.135,0.177 10 true 3 2.063,1.698 2.198,1.875 0.135,0.177 10 true 4 1.052,0.031 1.188,0.208 0.135,0.177 10 true 6 0.99,0.604 1.125,0.781 0.135,0.177 10 false 2 1.25,1.615 1.396,1.792 0.146,0.177 10 true 5 2.177,0.292 2.313,0.469 0.135,0.177 10 false 1

Temporarily install the water pump and clamp bracket with the 4 bolts and 2 nuts.

Text in Illustration
*1 Clamp Bracket


d.

Tighten the 4 bolts and 2 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.

Install the wire of the crankshaft position sensor onto the clamp bracket.


f.

Install the clamp of the crankshaft position sensor onto the water pump.


Hide 16173 2.INSTALL WATER PUMP PULLEY

U188245E02
1.719,0.688 0.438,0.688 false 0.063,0.604 0.396,0.76 0.333,0.156 10 false SST

a.

Using SST, install the water pump pulley with the 4 bolts.

SST
09960-10010  (09962-01000, 09963-00700)

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 51217A 5.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 53292A 9.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 53701 10.INSTALL FRONT FENDER APRON RH

Hide 51441 11.INSTALL NO. 1 ENGINE UNDER COVER

Hide 12.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.