Home › Vehicle Interior › ENGINE HOOD / DOOR › BACK DOOR › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292029 BACK DOOR A

ENGINE HOOD / DOOR  BACK DOOR  REASSEMBLY  


PROCEDURE

Hide 84270G 1.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

a.
B139525

Install the sensor with the 2 clips and 2 screws.


b.

Connect the connector.


Hide 84280D 2.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

a.

Install the sensor with the 2 clips and 2 screws.


b.

Connect the connector.


Hide 69461 3.INSTALL BACK DOOR SIDE MALE STOPPER RH

a.
B139524

Install the stopper with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 67 in.*lbf)


Hide 69462 4.INSTALL BACK DOOR SIDE MALE STOPPER LH

a.

Install the stopper with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 67 in.*lbf)


Hide 84930 6.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY

a.
B139523

Install the switch with the 2 bolts.


b.

Connect the connector.


Hide 81270 7.INSTALL LICENSE PLATE LIGHT ASSEMBLY

Hide 76801 8.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 81580D 9.INSTALL REAR LIGHT ASSEMBLY RH

a.
E359926

Install the light with the clip.


b.
E130641

Install the 3 nuts.


c.

Connect the connector.


Hide 81590A 10.INSTALL REAR LIGHT ASSEMBLY LH

a.
E359926

Install the light with the clip.


b.
E130641

Install the 3 nuts.


c.

Connect the connector.


Hide 85110R 13.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 85143R 14.INSTALL REAR WIPER MOTOR GROMMET

Hide 85190R 15.INSTALL REAR WIPER ARM ASSEMBLY

Hide 84840G 16.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY (w/ Power Back Door)

a.
B139522

Install the switch.


b.

Connect the connector.


Hide 74811G 17.INSTALL DOOR PULL HANDLE

a.
B139521

Install the door pull handle.


Hide 69350 18.INSTALL BACK DOOR LOCK ASSEMBLY

a.
B139520

Install the door lock with the 3 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Install the connector.


Hide 67750 19.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

a.
B139519

Attach the 18 clips to install the trim doard.


Hide 62581H 20.INSTALL REAR WINDOW SIDE GARNISH RH

a.
B139518

Attach the 2 clips to install the garnish.


Hide 62582H 21.INSTALL REAR WINDOW SIDE GARNISH LH

a.

Attach the 2 clips to install the garnish.


Hide 67848 22.INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

a.
B139517

Attach the 3 clips to install the service hole cover.


Hide 67939D 23.INSTALL BACK DOOR GARNISH CENTER

a.
B462718

Attach the 4 clips to install the garnish.


Hide 67005 24.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

Hide 67005 25.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

Hide 26. PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.