Home › Vehicle Interior › ENGINE HOOD / DOOR › BACK DOOR › from 2016.05
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292029 BACK DOOR A

ENGINE HOOD / DOOR  BACK DOOR  REASSEMBLY  


PROCEDURE

Hide 81270 2.INSTALL LICENSE PLATE LIGHT ASSEMBLY

Hide 76802C 3.INSTALL NO. 2 BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 76801 4.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 6.INSTALL REAR LIGHT ASSEMBLY RH (except LED Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 8.INSTALL REAR LIGHT ASSEMBLY RH (for LED Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 85110R 9.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 85143R 10.INSTALL REAR WIPER MOTOR GROMMET

Hide 85190R 11.INSTALL REAR WIPER ARM ASSEMBLY

Hide 84280D 12.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

a.

for Upper Side:

i.
B450891

Install the power back door sensor assembly LH with the clip and 3 screws.


ii.

Connect the connector.



Hide 84280D 13.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

a.

for Lower Side:

i.
B450890

Install the power back door sensor assembly LH with the clip and 2 screws.


ii.

Connect the connector.



Hide 84270G 14.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

a.

for Upper Side:

HINT:

Use the same procedure as for the LH side.



Hide 84270G 15.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

a.

for Lower Side:

HINT:

Use the same procedure as for the LH side.



Hide 69461 16.INSTALL BACK DOOR SIDE MALE STOPPER RH

a.
B139524

Install the stopper with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 67 in.*lbf)


Hide 69462 17.INSTALL BACK DOOR SIDE MALE STOPPER LH

a.

Install the stopper with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 67 in.*lbf)


Hide 69350 18.INSTALL BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

a.
B139520

Install the back door lock assembly with the 3 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Install the connector.


Hide 69350 19.INSTALL BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)

a.
B141629

Install the back door lock assembly with the 3 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Install the connector.


Hide 69321 20.INSTALL BACK DOOR LOCK COVER

a.
B450889

Attach the 4 claws to install the back door lock cover.


Hide 84930 21.INSTALL DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)

a.
B139522

Install the switch.


b.

Connect the connector.


Hide 74811G 22.INSTALL DOOR PULL HANDLE

a.
B139521

Install the door pull handle.


Hide 67750 23.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

a.
B139519

Attach the 18 clips to install the trim board.


Hide 62581H 24.INSTALL REAR WINDOW SIDE GARNISH RH

a.
B139518

Attach the 2 clips to install the garnish.


Hide 62582H 25.INSTALL REAR WINDOW SIDE GARNISH LH

a.

Attach the 2 clips to install the garnish.


Hide 67848 26.INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

a.
B139517

Attach the 3 clips to install the service hole cover.


Hide 67939D 27.INSTALL BACK DOOR CENTER GARNISH

a.
B462718

Attach the 4 clips to install the garnish.


Hide 67005 28.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

Hide 67005 29.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

Hide 30. PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.