Home › Drivetrain › K112 (CVT) › DIFFERENTIAL OIL SEAL › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292054 DIFFERENTIAL OIL SEAL A

K112 CVT  DIFFERENTIAL OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 53702 2.REMOVE FRONT FENDER APRON LH

Hide 3.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C128915

Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the continuously variable transaxle assembly.


b.
C242825E02
2.417,0.688 2.615,0.688 true 2.646,0.604 2.833,0.76 0.188,0.156 10 false *1

Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube from the continuously variable transaxle assembly and drain the continuously variable transaxle fluid.

Text in Illustration
*1 No. 1 Transmission Oil Filler Tube


c.

Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube to the continuously variable transaxle assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


d.

Temporarily install the gasket and overflow plug.

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



Hide 4.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 30400C 5.REMOVE CVT TYPE T OIL SEAL LH

C103977E02
0.895,2.315 1.208,2.462 0.313,0.147 10 SST 1.051,1.163 1.051,2.278 false 1.928,2.815 2.241,2.962 0.313,0.147 10 SST 2.117,2.573 2.117,2.778 false

a.

Using SST, remove the oil seal from the transaxle case.

SST
09308-00010  

NOTICE:

Do not damage the transaxle case.



Hide 30400B 6.REMOVE CVT TYPE T OIL SEAL RH

C189644E01
0.078,1.416 0.395,1.557 0.317,0.141 10 SST 0.946,0.997 0.449,1.495 0.449,1.495 1.251,1.775 false

a.

Using SST, remove the oil seal from the transaxle housing.

SST
09308-00010  

NOTICE:

Do not damage the transaxle housing.



Hide 30400C 7.INSTALL CVT TYPE T OIL SEAL LH

C194180E03
1.406,2.448 2.042,2.583 true 1.521,0.99 3,0.448 3,0.448 2.229,1.021 true 3.031,0.354 3.323,0.51 0.292,0.156 10 false SST 1.094,2.365 1.385,2.521 0.292,0.156 10 false SST

a.

Using SST and a hammer, tap in a new oil seal to the transaxle case.

SST
09726-27012  (09726-02041)
09950-70010  (09951-07200)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the oil seal lip.



b.

Coat the lip of the oil seal with MP grease.


Hide 30400B 8.INSTALL CVT TYPE T OIL SEAL RH

C211790E01
2.808,1.147 3.103,1.289 0.295,0.142 10 SST 0.865,2.499 1.160,2.641 0.295,0.142 10 SST 1.834,1.189 2.766,1.23 2.766,1.23 1.68,1.266 false 1.209,2.567 1.768,2.567 false

a.

Using SST and a hammer, tap in a new oil seal to the transaxle housing.

SST
09387-00010  
09950-70010  (09951-07200)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the oil seal lip.



b.

Coat the lip of the oil seal with MP grease.


Hide 9.INSTALL FRONT DRIVE SHAFT ASSEMBLY

Hide 10.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 53702 11.INSTALL FRONT FENDER APRON LH

Hide 13.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 14.CHECK ABS SPEED SENSOR SIGNAL