Home › Drivetrain › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY › from 2016.05
RM24M0E _52 Drivetrain _059580 DRIVE SHAFT _0292135 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT  FRONT DRIVE SHAFT ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 43420 1.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

C127700

a.

Coat the spline of the inboard joint shaft with gear oil.


b.

Using a brass bar and hammer, align the shaft splines in the drive shaft.

NOTICE:
·

Set the snap ring with the opening side facing downwards.

·

Be careful not to damage the oil seal, boot and dust cover.




Hide 43410 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

a.

Coat the spline of the inboard joint shaft with gear oil.


b.
C127638

Align the shaft spline and install the drive shaft with 2 bolts.

Torque:
51 N*m (515 kgf*cm, 37 ft.*lbf)

NOTICE:

Do not damage the oil seal, boot and dust cover.



Hide 3.CONNECT STEERING KNUCKLE WITH AXLE HUB LH

a.
U186063E01
2.239,1.351 2.957,1.491 0.718,0.140 10 Matchmark 1.63,0.837 2.226,1.402 false 2.226,1.402 1.702,1.054 false

Align the matchmarks and connect the front drive shaft assembly to the front steering knuckle with axle hub.


Hide 4.CONNECT STEERING KNUCKLE WITH AXLE HUB RH

HINT:

Use the same procedures described for the LH side.


Hide 48069 5.CONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH

Hide 48068 6.CONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

Hide 48810 7.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 8.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

Hide 45046 9.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 10.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 89542 12.INSTALL FRONT SPEED SENSOR RH

HINT:

Use the same procedures described for the LH side.


Hide 47750 13.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.
C162626

Install the caliper with the 2 bolts.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)


Hide 47730 14.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 43502H 15.INSTALL FRONT AXLE HUB NUT (for 2AZ-FE)

Hide 43502H 16.INSTALL FRONT AXLE HUB NUT (for 2GR-FE)

Hide 53702 17.INSTALL FRONT FENDER APRON LH

Hide 18.INSTALL FRONT WHEEL

T = 103 N*m{ 1,050 kgf*cm 76 ft.*lbf }

Hide 19.ADD AUTOMATIC TRANSAXLE FLUID (for 2AZ-FE, Automatic Transaxle)

Hide 20.ADD AUTOMATIC TRANSAXLE FLUID (for 2GR-FE)

Hide 21.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 22.INSPECT FOR OIL LEAK

Hide 23.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

a.

Inspect and adjust the front wheel alignment (see page Suspension>SUSPENSION>FRONT WHEEL ALIGNMENT>ADJUSTMENT).