Home › Suspension › SUSPENSION › REAR COIL SPRING › 2014.09–2016.05
RM24M0E _53 Suspension _059582 SUSPENSION _0292146 REAR COIL SPRING A

SUSPENSION  REAR COIL SPRING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 48258C 1.INSTALL REAR COIL SPRING INSULATOR LOWER LH

C137758E02
2.042,0.208 1.594,0.208 false 1.604,0.208 1.604,0.385 false 2.094,0.125 3.094,0.292 1,0.167 10 false Insulator Lower 2.719,2.135 3.271,2.469 0.552,0.333 10 false Front of Vehicle

a.

Install the insulator lower to the rear axle beam.


Hide 48231B 2.INSTALL REAR COIL SPRING LH

C137759E03
2.406,0.521 2.177,1.729 true 2.542,0.521 2.406,0.521 false 0.604,2.771 0.604,3.115 false 3.177,1.76 2.99,2.104 false 2.99,2.104 2.99,2.906 false 0.76,0.333 0.938,0.333 false 0.938,0.333 0.938,0.833 false 2.594,0.438 3.313,0.75 0.719,0.313 10 false Coil Spring Stopper 2.417,2.927 3.375,3.094 0.958,0.167 10 false 10 mm or Less 0.229,3.125 1.219,3.281 0.99,0.156 10 false Lower Insulator 0.073,0.25 0.76,0.635 0.688,0.385 10 true Coil Spring

a.

Align the stopper part of the insulator lower with the coil spring tip, and install the coil spring.

HINT:

Install the coil spring so that there is 10 mm (0.39 in.) or less of clearance between the coil spring tip and insulator stopper part.



Hide 48259A 3.INSTALL REAR COIL SPRING INSULATOR UPPER LH

C137760E03
1.573,0.125 1.573,0.719 false 1.573,0.115 1.813,0.115 false 2.375,0.5 2.146,0.5 false 2.146,0.5 2.146,1.74 true 3.177,1.76 2.948,1.99 false 2.948,1.99 2.948,2.917 false 0.948,0.365 1.146,0.365 false 1.146,0.365 1.146,0.771 false 1.854,0.042 2.844,0.208 0.99,0.167 10 false Upper Insulator 2.448,2.948 3.375,3.115 0.927,0.167 10 false 10 mm or less 2.438,0.427 3.156,0.76 0.719,0.333 10 false Coil Spring Stopper 0.25,0.271 0.969,0.5 0.719,0.229 10 false Coil Spring

a.

Align the stopper part of the insulator upper with the coil spring tip, and install the insulator upper.

HINT:

Install the coil spring so that there is 10 mm (0.39 in.) or less of clearance between the coil spring tip and insulator stopper part.



Hide 48540 4.INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

a.

Slowly raise the rear axle beam with a jack, and connect the shock absorber to the rear axle beam.

NOTICE:

Place a wooden or rubber block between the jack and arm.



b.
C133579

Install the shock absorber with the bolt and nut.

NOTICE:

Do not tighten the nut.


Torque:
58 N*m (592 kgf*cm, 43 ft.*lbf)


Hide 46430 5.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 46420 6.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

Hide 8.INSTALL REAR WHEEL

T = 103 N*m{ 1,050 kgf*cm 76 ft.*lbf }

Hide 10.CHECK SPEED SENSOR SIGNAL

Hide 11.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

a.

Inspect and adjust the rear wheel alignment (see page Suspension>SUSPENSION>REAR WHEEL ALIGNMENT>ADJUSTMENT).