Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0210/33  Right Rear Wheel Speed Sensor Signal  C0215/34  Left Rear Wheel Speed Sensor Signal  C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1277/77  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278/78  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1332/38  Right Rear Speed Sensor Circuit  C1333/39  Left Rear Speed Sensor Circuit  


DESCRIPTION

Refer to DTC C0200/31 (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C0200/31).

DTCs C1273/73, C1274/74, C1277/77 and C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1273/73, C1274/74, C1277/77 and C1278/78 are output only in the test mode.

DTC No. DTC Detection Condition Trouble Area
C0210/33
C0215/34
When one of following conditions is met:
1.

Vehicle speed is more than 40 km/h (25 mph) and pulses are not input for 0.01 second.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 18 km/h (11 mph), the rear wheel speed of 0 km/h (0 mph) is detected.


·

Rear speed sensor

·

Rear speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1273/73
C1274/74
Detected only during test mode.
·

Rear speed sensor

·

Rear speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1277/77
C1278/78
Detected only during test mode.
·

Rear speed sensor

·

Rear speed sensor circuit

·

Sensor installation


C1332/38
C1333/39
Abnormality in the resistance value of each speed sensor is detected.
·

Rear speed sensor RH and/or LH

·

Rear speed sensor circuit RH and/or LH

·

Sensor installation

·

ABS and TRACTION actuator



HINT:
·

DTC C0210/33 and C1332/38 relate to the rear speed sensor RH.

·

DTC C0215/34 and C1333/39 relate to the rear speed sensor LH.



WIRING DIAGRAM

C143427E05
5.667,2.969 6.865,3.354 1.198,0.385 10 false A9 0.771,0.646 2.344,1.01 1.573,0.365 10 false d1 0.771,2 2.344,2.365 1.573,0.365 10 false c1 2.302,0.469 2.458,0.625 0.156,0.156 10 false 2 2.302,1.135 2.448,1.323 0.146,0.188 10 false 1 2.302,1.781 2.458,1.938 0.156,0.156 10 false 2 2.302,2.448 2.448,2.635 0.146,0.188 10 false 1 5.906,0.417 6.219,0.604 0.313,0.188 10 false RL+ 5.906,1.167 6.219,1.354 0.313,0.188 10 false RL- 5.906,1.729 6.219,1.917 0.313,0.188 10 false RR+ 5.906,2.49 6.219,2.677 0.313,0.188 10 false RR- 5.646,0.573 5.865,0.74 0.219,0.167 10 false 6 5.583,1.323 5.802,1.49 0.219,0.167 10 false 27 5.646,1.885 5.865,2.052 0.219,0.167 10 false 8 5.583,2.635 5.802,2.802 0.219,0.167 10 false 29 0.76,2.177 2.333,2.542 1.573,0.365 10 false Rear Speed Sensor RH 0.781,0.823 2.354,1.188 1.573,0.365 10 false Rear Speed Sensor LH 5.667,3.135 6.865,3.521 1.198,0.385 10 false Skid Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal in test mode after cleaning or replacement (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION)
a.

Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness corresponding to a DTC (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open RR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-
RL Speed Open RL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-

OK:

There are no momentary interruptions.


HINT:

Perform this inspection before removing the sensor and connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
a.

Check the Data List for proper functioning of the rear speed sensor.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202.8 mph) Similar to speed indicated on speedometer -
RL Wheel Speed Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202.8 mph) Similar to speed indicated on speedometer -

OK:

There is almost no difference between actual wheel speed and displayed speed value.


HINT:

There is a tolerance of +-10% in the speedometer indication.




OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.INSPECT REAR SPEED SENSOR (INSTALLATION)
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Perform a TEST MODE inspection and check for DTCs (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

No DTCs output.




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B

9.REPLACE REAR SPEED SENSOR
5.INSPECT REAR SPEED SENSOR (INSTALLATION)
a.
C140169E03
0.979,1.396 1.167,1.646 false 0.354,1.698 0.625,1.865 0.271,0.167 10 false OK 2.875,1.708 3.146,1.875 0.271,0.167 10 false NG 0.896,1.667 1.771,1.813 0.875,0.146 10 false No Clearance

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle carrier.



HINT:

Check the speed sensor signal after the replacement (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



OK

6.CHECK REAR SPEED SENSOR (TIP)

NG

CHECK AND REPLACE REAR SPEED SENSOR

6.CHECK REAR SPEED SENSOR (TIP)
a.

Remove the rear speed sensor.


b.

Check the sensor tip.

OK:

No scratches or foreign matter on the sensor tip.




OK

7.CHECK WIRE HARNESS (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

CLEAR OR REPLACE REAR SPEED SENSOR

7.CHECK WIRE HARNESS (SKID CONTROL ECU - REAR SPEED SENSOR)
a.
U189321E02
1.438,1.406 0.948,1.854 false 1.594,1.396 2.823,0.979 false 1.646,1.5 1.969,1.958 false 1.469,1.49 1.542,1.948 false 0.135,0.063 1.5,0.24 1.365,0.177 10 false Wire Harness Side: 1.167,0.5 2.313,0.646 1.146,0.146 10 false Skid Control ECU 0.135,0.667 0.385,0.885 0.25,0.219 10 false A9 0.146,2.708 0.396,2.927 0.25,0.219 10 false d1 1.938,2.74 2.188,2.958 0.25,0.219 10 false c1 0.385,2.281 1.656,2.458 1.271,0.177 10 false Rear Speed Sensor 2.885,0.865 3.219,1.01 0.333,0.146 10 false RR+ 0.75,1.854 1.083,2 0.333,0.146 10 false RL+ 2.01,1.979 2.344,2.125 0.333,0.146 10 false RR- 1.49,1.969 1.823,2.115 0.333,0.146 10 false RL-

Disconnect the A9 ECU connector.


b.

Disconnect d1 and c1 sensor connectors.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LH:
Tester Connection Specified Condition
A9-6 (RL+) - d1-2 Below 1 Ω
A9-27 (RL-) - d1-1 Below 1 Ω
A9-6 (RL+) - Body ground 10 kΩ or higher
A9-27 (RL-) - Body ground 10 kΩ or higher

for RH:
Tester Connection Specified Condition
A9-8 (RR+) - c1-2 Below 1 Ω
A9-29 (RR-) - c1-1 Below 1 Ω
A9-8 (RR+) - Body ground 10 kΩ or higher
A9-29 (RR-) - Body ground 10 kΩ or higher




OK

8.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

9.REPLACE REAR SPEED SENSOR

B

END

9.REPLACE REAR SPEED SENSOR

NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output (for 2AZ-FE) A
DTC is output (for 2GR-FE) B
DTC is not output C



A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C

END