Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF indicator and VSC OFF indicator lights will come on.

WIRING DIAGRAM

C239016E26
1.385,0.813 1.698,1.01 0.313,0.198 10 false 31 1.385,1.615 1.698,1.813 0.313,0.198 10 false 32 0.917,0.927 1.531,1.156 0.615,0.229 10 false CANL 0.906,1.729 1.417,1.99 0.51,0.26 10 false CANH 0.323,3.927 0.635,4.125 0.313,0.198 10 false G28 0.323,4.094 1.521,4.51 1.198,0.417 10 false Combination Meter Assembly 3.781,2.771 4.094,2.969 0.313,0.198 10 false 3 4.833,2.771 5.146,2.969 0.313,0.198 10 false 6 3.948,2.979 4.26,3.177 0.313,0.198 10 false E 4.646,2.99 4.958,3.188 0.313,0.198 10 false + 3.833,3.24 4.281,3.458 0.448,0.219 10 false G101 3.844,3.406 5.031,3.646 1.188,0.24 10 false VSC OFF Switch 5.698,0.823 6.01,1.021 0.313,0.198 10 false 14 5.698,1.635 6.01,1.833 0.313,0.198 10 false 35 5.688,2.771 6,2.969 0.313,0.198 10 false 17 5.948,0.927 6.406,1.146 0.458,0.219 10 false CANL 5.938,1.75 6.427,2.01 0.49,0.26 10 false CANH 5.948,2.875 6.375,3.104 0.427,0.229 10 false CSW 5.094,3.75 5.406,3.948 0.313,0.198 10 false A9 5.083,3.938 7.01,4.385 1.927,0.448 10 false Skid Control ECU (ABS and TRACTION Actuator Assembly)

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
Unknown: Unspecified
VSC OFF: VSC off mode
-


d.

Check the indicator light and mode condition on the intelligent tester changes according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display TRC OFF Indicator Light VSC OFF Indicator Light
Not pressed Normal Does not come on Does not come on
Pressing the VSC OFF switch TRC OFF Comes on Does not come on
Pressing and holding the VSC OFF switch VSC OFF Comes on Comes on


Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display is normal. C




A

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observe combination meter
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter


b.

Check the TRC OFF indicator and VSC OFF indicator lights on the combination meter assembly turn ON or OFF in accordance with intelligent tester operation.

OK:

The TRC OFF indicator and VSC OFF indicator lights turn ON or OFF in accordance with intelligent tester operation.




OK

5.INSPECT VSC OFF SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VSC OFF SWITCH
a.
C239020E09
0.171,0.138 2.715,0.481 2.545,0.343 10 Component without harness connected: (VSC OFF Switch) 1.898,2.028 2.474,2.87 false 1.527,2.028 0.952,2.87 false 2.431,2.883 2.559,3.046 0.128,0.163 10 E 0.849,2.883 0.978,3.046 0.128,0.163 10 +

Turn the engine switch off.


b.

Disconnect the G101 VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (+) - 3 (E) Switch is pushed in Below 1 Ω
6 (+) - 3 (E) Switch is not pushed in 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.
C366267E01
0.167,0.667 0.583,0.917 0.417,0.25 0.25,3.25 0.667,3.5 0.417,0.25 1.25,4.323 1.385,4.052 false 1.865,4.313 1.781,4.063 false 2.167,1.833 2.333,1.302 false 0.188,0.042 2.438,0.406 2.25,0.365 10 false Front view of wire harness connector: (to Skid Control ECU) 0.271,0.698 0.677,0.927 0.406,0.229 10 false A9 1.958,1.854 2.365,2.083 0.406,0.229 10 false CSW 0.229,2.292 2.51,2.708 2.281,0.417 10 false Front view of wire harness connector: (to VSC OFF Switch) 1.156,4.333 1.563,4.563 0.406,0.229 10 false E 1.865,4.333 2.271,4.563 0.406,0.229 10 false + 0.281,3.292 0.688,3.521 0.406,0.229 10 false G101

Disconnect the A9 skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A9-17 (CSW) - G101-6 (+) Always Below 1 Ω
A9-17 (CSW) - Body ground Always 10 kΩ or higher
G101-6 (+) - Body ground Always 10 kΩ or higher
G101-3 (E) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (for 2AZ-FE) A
OK (for 2GR-FE) B
NG C


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the engine switch off.


b.

Perform the Active Test of the combination meter assembly using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The TRC OFF indicator and VSC OFF indicator lights turn on or off in accordance with intelligent tester operation.


Result:
Result Proceed to
OK (for 2AZ-FE) A
OK (for 2GR-FE) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C