The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level. The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1429 | Open or Short in Brake Pedal Load Sensing Switch | An open or short in the brake pedal load sensing switch circuit continues for 0.5 seconds or more. | ·
Brake pedal load sensing switch (brake pedal support assembly) ·
Brake pedal load sensing switch circuit ·
Skid control ECU (brake actuator assembly) |
When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
When C1249, C1425 and/or C1426 is output together with C1429, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249 for C1249, Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425 for C1425 and/or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426 for C1426).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch / ON or OFF | ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point |
- |
Check that the brake pedal load sensing switch display observed on the GTS changes according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
OK
NG
Turn the engine switch off.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1429 is not output. | A |
| DTC C1429 is output. | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Turn the engine switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A24 brake pedal load sensing switch (brake pedal support assembly) connector.
Do not remove the brake pedal load sensing switch from the brake pedal support assembly.
When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FSW+) - 1 (FSW-) | Switch OFF (Brake pedal depressed) | 950 to 1050 Ω |
| 2 (FSW+) - 1 (FSW-) | Switch ON (Brake pedal released) | 203 to 223 Ω |
| *a | Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly)) |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A35 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-34 (FSW+) - A24-2 (FSW+) | Always | Below 1 Ω |
| A35-34 (FSW+) or A24-2 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A24-1 (FSW-) - Body ground | Always | Below 1 Ω |
OK
NG