Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit An open in the stop light switch assembly input line continues for 3 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off




OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189564E02
1.51,1.531 1.74,0.74 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.25,0.781 0.542,0.938 0.292,0.156 10 false A35 1.75,0.573 2.042,0.729 0.292,0.156 10 false STP

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
A35-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:
·

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly (See page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).

OK:

The stop light switch assembly is normal.




OK

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189564E02
1.51,1.531 1.74,0.74 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.25,0.781 0.542,0.938 0.292,0.156 10 false A35 1.75,0.573 2.042,0.729 0.292,0.156 10 false STP

Reconnect the A33 stop light switch assembly connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
A35-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.




OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189912E01
0.517,1.228 0.806,1.431 0.289,0.204 10 A34 0.276,0.299 0.555,0.676 0.279,0.376 10 *a 1.564,1.089 1.870,1.293 0.306,0.204 10 STP 1.531,1.896 1.676,1.307 false

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A34 stop light control relay connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
A34-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay)

HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.




OK

8.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

8.RECONFIRM DTC
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the A34 stop light control relay connector.



d.

Turn the engine switch off.


e.

Start the engine.


f.

Depress the brake pedal several times to test the stop light circuit.


g.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:
·

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL).

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





A

B