Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1429  Open or Short in Brake Pedal Load Sensing Switch  


DESCRIPTION

The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level. The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1429 Open or Short in Brake Pedal Load Sensing Switch An open or short in the brake pedal load sensing switch circuit continues for 0.5 seconds or more.
·

Brake pedal load sensing switch (brake pedal support assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C359911E02
2.125,1.104 2.281,1.302 0.156,0.198 10 false 1 4.208,1.104 4.365,1.302 0.156,0.198 10 false 2 1.771,1.104 1.927,1.302 0.156,0.198 10 false 1 1.677,1.354 1.969,1.552 0.292,0.198 10 false A40 4.125,1.354 4.417,1.552 0.292,0.198 10 false A40 2.042,1.354 2.333,1.552 0.292,0.198 10 false A38 4.49,1.354 4.781,1.552 0.292,0.198 10 false A38 1.729,1.583 1.885,1.781 0.156,0.198 10 false *1 2.083,1.583 2.24,1.781 0.156,0.198 10 false *2 4.188,1.583 4.344,1.781 0.156,0.198 10 false *1 4.542,1.583 4.698,1.781 0.156,0.198 10 false *2 4.563,1.104 4.719,1.302 0.156,0.198 10 false 2 5.552,1.24 5.781,1.438 0.229,0.198 10 false 34 5.823,1.323 6.302,1.49 0.479,0.167 10 false FSW+ 2.156,2.135 4.323,2.469 2.167,0.333 10 false Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly) 5.448,3.031 7.042,3.385 1.594,0.354 10 false Skid Control ECU (Brake Actuator Assembly) 0.927,3.365 1.698,3.573 0.771,0.208 10 false *1: for LHD 2,3.365 2.771,3.573 0.771,0.208 10 false *2: for RHD 3.625,1.135 4.104,1.302 0.479,0.167 10 false FSW+ 2.427,1.135 2.906,1.302 0.479,0.167 10 false FSW- 5.448,2.875 5.792,3.042 0.344,0.167 10 false A35

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When C1249, C1425 and/or C1426 is output together with C1429, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249 for C1249, Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425 for C1425 and/or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426 for C1426).


PROCEDURE

1.READ VALUE USING GTS (BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-


d.

Check that the brake pedal load sensing switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

2.RECONFIRM DTC

NG

3.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
2.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Perform a road test.



Result:
Result Proceed to
DTC C1429 is not output. A
DTC C1429 is output. B



A

B

3.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.
C239141E12
1.552,2.052 0.969,2.854 false 1.833,2.052 2.417,2.854 false 0.271,0.229 0.479,0.417 0.208,0.188 10 false *a 0.688,2.885 1.146,3.073 0.458,0.188 10 false FSW+ 2.292,2.885 2.75,3.073 0.458,0.188 10 false FSW-

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A38 or A40 brake pedal load sensing switch (brake pedal support assembly) connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW+) - 1 (FSW-) Switch OFF (Brake pedal depressed) 950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Switch ON (Brake pedal released) 203 to 223 Ω


Text in Illustration
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for LHD

Tester Connection Condition Specified Condition
A35-34 (FSW+) - A40-2 (FSW+) Always Below 1 Ω
A35-34 (FSW+) or A40-2 (FSW+) - Body ground Always 10 kΩ or higher
A40-1 (FSW-) - Body ground Always Below 1 Ω

for RHD

Tester Connection Condition Specified Condition
A35-34 (FSW+) - A38-2 (FSW+) Always Below 1 Ω
A35-34 (FSW+) or A38-2 (FSW+) - Body ground Always 10 kΩ or higher
A38-1 (FSW-) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR