Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1426  Stop Light Switch OFF Stuck Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect a short in the stop light input line or the ground line of the stop light circuit with the stop light switch assembly on (brake pedal depressed).

If the skid control ECU (brake actuator assembly) detects a short in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1426 Stop Light Switch OFF Stuck Malfunction Either of the following is detected:
1.

With the stop light switch assembly off, the stop light switch assembly is judged to be on based on the master cylinder pressure value for 3 seconds or more.

2.

With the stop light switch assembly off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more.


·

Wire harness or connector (STP circuit)

·

Wire harness or connector (GND1 circuit)

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height installation (See page Brake>BRAKE>BRAKE PEDAL>ADJUSTMENT).


b.

Check the stop light switch assembly installation (See page Brake>BRAKE>BRAKE PEDAL>INSTALLATION).

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and switch before inspecting the input signals and other related parts.




OK

2.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off




OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

7.INSPECT STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
4.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1426 is not output. A
DTC C1426 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189564E02
1.51,1.531 1.74,0.74 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.25,0.781 0.542,0.938 0.292,0.156 10 false A35 1.75,0.573 2.042,0.729 0.292,0.156 10 false STP

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.




OK

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U189563E02
2.729,1.5 2.292,0.771 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.24,0.792 0.531,0.948 0.292,0.156 10 false A35 2.031,0.594 2.49,0.75 0.458,0.156 10 false GND1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

7.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly (See page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light switch assembly is normal.




OK

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189564E02
1.51,1.531 1.74,0.74 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.25,0.781 0.542,0.938 0.292,0.156 10 false A35 1.75,0.573 2.042,0.729 0.292,0.156 10 false STP

Reconnect the A37 stop light switch assembly connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
A35-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.




OK

9.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

9.RECONFIRM DTC
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1426 is not output. A
DTC C1426 is output. B


HINT:
·

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL).

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





A

B