Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1246  Master Cylinder Pressure Sensor Malfunction  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

DTC C1281 is cleared when the Lost Booster Pressure Judgment Check is performed correctly in Test Mode and the check indicates a pass, or when Test Mode ends. DTC C1281 is output only in Test Mode.

C106656E64
3.896,4.146 5.531,4.427 1.635,0.281 10 false Brake Actuator Assembly 2.906,1.167 4.094,1.396 1.188,0.229 10 false Skid Control ECU 5.417,2.417 6.479,2.969 1.063,0.552 10 false Master Cylinder Pressure Sensor 0.573,1.979 1.448,2.229 0.875,0.25 10 false from Battery 0.26,2.604 1.354,3.125 1.094,0.521 10 false from Stop Light Switch Assembly 0.365,3.385 1.406,3.615 1.042,0.229 10 false to Body Ground 2.76,1.99 3.198,2.188 0.438,0.198 10 false +BS 2.76,2.677 3.208,2.885 0.448,0.208 10 false STP 2.76,3.385 3.281,3.583 0.521,0.198 10 false GND 3.865,1.99 4.333,2.198 0.469,0.208 10 false VCM 3.865,2.677 4.313,2.885 0.448,0.208 10 false PMC 4,3.385 4.313,3.604 0.313,0.219 10 false E2 0.49,4.708 4.854,4.917 4.365,0.208 10 false VCM: Master Cylinder Pressure Sensor Power Supply 0.49,5.063 3.917,5.271 3.427,0.208 10 false PMC: Master Cylinder Pressure Sensor Input 0.5,5.417 3.979,5.635 3.479,0.219 10 false E2: Master Cylinder Pressure Sensor Ground

DTC No. Detection Item DTC Detection Condition Trouble Area
C1246 Master Cylinder Pressure Sensor Malfunction Any of the following is detected:
·

The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V).

·

An abnormality is detected in the skid control ECU internal sensor test.

·

The sensor signal offset value is out of range.


·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder pressure sensor (brake actuator assembly)


C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) Detected only during Test Mode.
·

Stop light switch assembly

·

Brake pedal load sensing switch (brake pedal support assembly)

·

Brake booster assembly

·

Master cylinder pressure sensor (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off




OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)

NG

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-


d.

Check that the stop light switch assembly display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



e.

Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch turn on.

OK:

First the stop light switch assembly turns on, and then the brake pedal load sensing switch turns on.



Result:
Result Proceed to
OK A
NG (The stop light switch assembly does not turn on.) B
NG (Turning on of the brake pedal load sensing switch is not confirmed.) C
NG (The brake pedal load sensing switch turns on first.) D



A

3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

C

6.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

D

8.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.20 to 0.40 V Reading increases when brake pedal is depressed


b.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the voltage displayed on the GTS increases.




OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 30 km/h (18 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).



Result:
Result Proceed to
DTC C1246 is not output. A
DTC C1246 is output. B



A

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189564E02
1.51,1.531 1.74,0.74 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.25,0.781 0.542,0.938 0.292,0.156 10 false A35 1.75,0.573 2.042,0.729 0.292,0.156 10 false STP

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
A35-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:
·

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.
C239141E13
1.563,2.073 0.979,2.875 false 1.823,2.073 2.406,2.875 false 0.271,0.229 0.479,0.417 0.208,0.188 10 false *a 0.688,2.927 1.146,3.115 0.458,0.188 10 false FSW+ 2.25,2.927 2.708,3.115 0.458,0.188 10 false FSW-

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A38 or A40 brake pedal load sensing switch (brake pedal support assembly) connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW+) - 1 (FSW-) Switch OFF (Brake pedal depressed) 950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Switch ON (Brake pedal released) 203 to 223 Ω


Text in Illustration
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for LHD

Tester Connection Condition Specified Condition
A35-34 (FSW+) - A40-2 (FSW+) Always Below 1 Ω
A35-34 (FSW+) or A40-2 (FSW+) - Body ground Always 10 kΩ or higher
A40-1 (FSW-) - Body ground Always Below 1 Ω

for RHD

Tester Connection Condition Specified Condition
A35-34 (FSW+) - A38-2 (FSW+) Always Below 1 Ω
A35-34 (FSW+) or A38-2 (FSW+) - Body ground Always 10 kΩ or higher
A38-1 (FSW-) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the engine switch off.


b.

Check the brake pedal height and stop light switch assembly installation (See page Brake>BRAKE>BRAKE PEDAL>ADJUSTMENT).

OK:

The brake pedal height and stop light switch assembly installation are normal.




OK

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY