Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(w/ VSC) › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292165 BRAKE ACTUATOR(w/ VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/ VSC)  INSTALLATION  


PROCEDURE

Hide 44510 1.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C302805E02
2.094,0.979 2.281,1.177 0.188,0.198 10 false 2 0.917,1.167 1.104,1.365 0.188,0.198 10 false 1 2.26,0 2.448,0.198 0.188,0.198 10 false 3

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Tighten the 3 nuts in the order shown in the illustration.




Hide 2.INSTALL BRAKE ACTUATOR WITH BRACKET

a.

Temporarily install the brake actuator with bracket.

NOTICE:

Do not damage the brake lines.



b.

Install the 3 nuts to secure the brake actuator with bracket.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Install the brake actuator with bracket while avoiding the brake lines.



c.

Engage the tube clamp to the brake actuator bracket assembly.


d.

Engage the wire harness clamp to the brake actuator bracket assembly.


e.
C302802E02
1.677,0.417 1.823,0.583 0.146,0.167 10 true B 1.438,3.75 1.583,3.917 0.146,0.167 10 true A

Connect the connector to the brake actuator assembly and disengage the claw (B).

NOTICE:
·

Do not allow water, oil or dirt to enter the connector.

·

Make sure that the actuator connector can be connected smoothly.




f.

Pull down the lock lever to engage the claw (A) and engage the connector lock.

NOTICE:

Make sure that the connector is locked securely.



g.
C311048E02
2.531,2.604 2.01,1.99 true 1.656,2 1.25,2.74 true 1.604,1.76 1.938,1.063 true 1.75,1.76 2.229,1.323 true 1.906,1.76 2.427,1.573 true 2.073,1.802 2.458,1.906 true 2.563,2.573 2.792,2.76 0.229,0.188 10 true *a 1.146,2.76 1.375,2.948 0.229,0.188 10 true *b 1.917,0.906 2.146,1.094 0.229,0.188 10 false *c 2.219,1.177 2.448,1.365 0.229,0.188 10 false *d 2.448,1.469 2.677,1.656 0.229,0.188 10 true *e 2.49,1.865 2.719,2.052 0.229,0.188 10 true *f 0.729,0.313 0.958,0.5 0.229,0.188 10 false *g

Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.

Text in Illustration
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH
*g Torque Wrench Fulcrum Length


h.

Using a union nut wrench, fully tighten the 2 brake lines (*a, *b).

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Do not kink or damage the brake lines.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):

18 N*m (184 kgf*cm, 13 ft.*lbf)




i.

Using a union nut wrench, fully tighten the 4 brake lines (*c, *d, *e, *f).

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Do not kink or damage the brake lines.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):

14 N*m (142 kgf*cm, 10 ft.*lbf)




Hide 17700 3.INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2AZ-FE)

Hide 17705 4.INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 2AZ-FE)

Hide 17700 5.INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2GR-FE)

Hide 17705 6.INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 2GR-FE)

Hide 11209 7.INSTALL V-BANK COVER SUB-ASSEMBLY (for 2GR-FE)

Hide 8.BLEED BRAKE SYSTEM

Hide 55712 9.INSTALL FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).