Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  


DESCRIPTION

This DTC is stored when the combination meter sub-assembly detects an open in a turn signal light circuit.

HINT:
·

If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.

·

If there is an open in a side turn signal light circuit, DTC B1507 will not be stored.



DTC No. DTC Detection Condition Trouble Area Note
B1507 When IG voltage is 10 V or more and the following condition is detected:
·

Open in front turn signal light circuit or rear turn signal light circuit


·

Bulb

·

LED

·

Harness or connector

·

Instrument panel junction block LH

·

Instrument panel junction block RH

·

Combination meter sub-assembly


w/ Multi-information Display

WIRING DIAGRAM

E349769E05
5.844,6 7.021,6.573 1.177,0.573 10 false Combination Meter Sub-assembly 5.833,5.833 6.229,6.146 0.396,0.313 10 false G123 6.104,0.49 6.719,0.854 0.615,0.365 10 false LL 6.104,5.396 6.656,5.698 0.552,0.302 10 false LR 3.781,0.458 4.396,0.823 0.615,0.365 10 false 4L 5.26,0.458 5.875,0.823 0.615,0.365 10 false 4A 3.76,3.771 4.375,4.135 0.615,0.365 10 false 4G 3.771,2.667 4.385,3.031 0.615,0.365 10 false 4D 5.271,5.396 5.885,5.76 0.615,0.365 10 false 5D 3.771,7.573 4.385,7.938 0.615,0.365 10 false 5D 3.781,5.396 4.396,5.76 0.615,0.365 10 false 5L 3.76,8.677 4.375,9.042 0.615,0.365 10 false 5G 3.813,0.271 4.125,0.521 0.313,0.25 10 false 7 5.896,0.365 6.208,0.615 0.313,0.25 10 false 7 5.26,0.271 5.573,0.521 0.313,0.25 10 false 14 3.771,2.448 4.083,2.698 0.313,0.25 10 false 14 3.823,3.563 4.135,3.813 0.313,0.25 10 false 8 5.271,5.177 5.583,5.427 0.313,0.25 10 false 24 3.781,7.365 4.094,7.615 0.313,0.25 10 false 25 3.823,5.177 4.135,5.427 0.313,0.25 10 false 1 3.771,8.479 4.083,8.729 0.313,0.25 10 false 17 2.521,0.354 2.75,0.604 0.229,0.25 10 false B 1.521,0.354 1.75,0.604 0.229,0.25 10 false E 2.729,0.344 2.958,0.594 0.229,0.25 10 false 1 1.313,0.354 1.542,0.604 0.229,0.25 10 false 3 1.302,1.438 1.531,1.688 0.229,0.25 10 false 1 2.74,1.427 2.969,1.677 0.229,0.25 10 false 2 2.51,2.563 2.74,2.813 0.229,0.25 10 false B 1.531,2.563 1.76,2.813 0.229,0.25 10 false E 1.542,5.281 1.771,5.531 0.229,0.25 10 false E 2.51,5.281 2.74,5.531 0.229,0.25 10 false B 3.177,2.458 3.365,2.708 0.188,0.25 10 false 5 2.76,2.458 3.052,2.708 0.292,0.25 10 false 10 0.833,2.469 1.021,2.719 0.188,0.25 10 false 11 1.25,2.479 1.438,2.729 0.188,0.25 10 false 4 2.729,3.656 2.958,3.906 0.229,0.25 10 false 4 1.323,3.646 1.552,3.896 0.229,0.25 10 false 3 2.719,5.281 2.948,5.531 0.229,0.25 10 false 1 1.323,5.271 1.552,5.521 0.229,0.25 10 false 3 2.729,6.375 2.958,6.625 0.229,0.25 10 false 2 1.313,6.375 1.542,6.625 0.229,0.25 10 false 1 2.729,8.563 2.958,8.813 0.229,0.25 10 false 4 1.313,8.583 1.542,8.833 0.229,0.25 10 false 3 0.583,0.865 3.5,1.25 2.917,0.385 10 false Headlight Assembly LH (Headlight Cord LH)*3 0.583,0.708 1.021,0.958 0.438,0.25 10 false B29 0.583,1.948 3.5,2.333 2.917,0.385 10 false Headlight Assembly LH (Headlight Cord LH)*4 0.583,1.771 1.021,2.021 0.438,0.25 10 false B22 0.875,3.052 3.229,3.438 2.354,0.385 10 false Side Turn Signal Light Assembly LH 0.667,4.146 3.094,4.531 2.427,0.385 10 false Rear Combination Light Assembly LH (Rear Turn Signal Light Socket LH) 0.667,3.979 1.104,4.229 0.438,0.25 10 false M43 0.583,5.781 3.5,6.167 2.917,0.385 10 false Headlight Assembly RH (Headlight Cord RH)*3 0.573,5.604 1.01,5.854 0.438,0.25 10 false B28 0.583,6.875 3.5,7.26 2.917,0.385 10 false Headlight Assembly RH (Headlight Cord RH)*4 0.583,6.698 1.021,6.948 0.438,0.25 10 false B23 0.667,9.073 3.052,9.458 2.385,0.385 10 false Rear Combination Light Assembly RH (Rear Turn Signal Light Socket RH) 0.656,8.917 1.094,9.167 0.438,0.25 10 false N45 5.333,6.74 6.656,7.406 1.323,0.667 10 false *1: w/ Ion Generator Sub-assembly 5.344,7.396 6.813,8.094 1.469,0.698 10 false *2: w/o Ion Generator Sub-assembly 5.333,8.083 6.781,8.469 1.448,0.385 10 false *3: for LED Headlight 5.344,8.458 7.146,8.844 1.802,0.385 10 false *4: except LED Headlight 3.479,4.188 5.802,4.573 2.323,0.385 10 false Instrument Panel Junction Block LH 3.51,9.083 5.833,9.469 2.323,0.385 10 false Instrument Panel Junction Block RH 2.781,2.865 2.969,3.063 0.188,0.198 10 false *1 0.844,2.854 1.031,3.052 0.188,0.198 10 false *1 3.156,2.854 3.333,3.052 0.177,0.198 10 false *2 1.208,2.854 1.385,3.052 0.177,0.198 10 false *2 2.74,2.667 3.063,2.917 0.323,0.25 10 false J11 0.802,2.667 1.125,2.917 0.323,0.25 10 false J11 3.115,2.656 3.438,2.906 0.323,0.25 10 false J13 1.167,2.656 1.49,2.906 0.323,0.25 10 false J13 2.51,7.469 2.74,7.719 0.229,0.25 10 false B 1.521,7.469 1.75,7.719 0.229,0.25 10 false E 3.177,7.375 3.365,7.625 0.188,0.25 10 false 5 2.75,7.385 3.042,7.635 0.292,0.25 10 false 10 0.844,7.385 1.031,7.635 0.188,0.25 10 false 11 1.25,7.385 1.438,7.635 0.188,0.25 10 false 4 0.875,7.958 3.24,8.344 2.365,0.385 10 false Side Turn Signal Light Assembly RH 2.771,7.771 2.958,7.969 0.188,0.198 10 false *1 0.833,7.771 1.021,7.969 0.188,0.198 10 false *1 3.146,7.771 3.323,7.969 0.177,0.198 10 false *2 1.198,7.771 1.375,7.969 0.177,0.198 10 false *2 2.729,7.573 3.052,7.823 0.323,0.25 10 false I11 0.823,7.563 1.146,7.813 0.323,0.25 10 false I11 3.115,7.573 3.438,7.823 0.323,0.25 10 false I13 1.177,7.573 1.5,7.823 0.323,0.25 10 false I13 5.833,5.292 6.146,5.542 0.313,0.25 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

Inspect the LEDs and bulbs for this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.

Result:
Result Proceed to
All LH turn signal lights do not blink A
All RH turn signal lights do not blink B
LH side turn signal lights do not flash at the correct speed C
RH side turn signal lights do not flash at the correct speed D




A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK LH)

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK RH)

C

6.CHECK TURN SIGNAL LIGHTS (LH SIDE)

D

11.CHECK TURN SIGNAL LIGHTS (RH SIDE)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK LH)
a.

Disconnect the G123 combination meter sub-assembly connector.


b.

Disconnect the 4A instrument panel junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-7 (LL) - 4A-14 Always Below 1 Ω




OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK LH
a.

Remove the instrument panel junction block LH.

U189990E02
1.844,0.396 2.177,0.563 0.333,0.167 10 false 4A 5.156,0.396 5.49,0.563 0.333,0.167 10 false 4D 1.844,2.135 2.177,2.302 0.333,0.167 10 false 4G 5.167,2.135 5.5,2.302 0.333,0.167 10 false 4L 0.24,0.094 0.573,0.26 0.333,0.167 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-14 - 4L-7 Always Below 1 Ω
4A-14 - 4D-14 Always Below 1 Ω
4A-14 - 4G-8 Always Below 1 Ω



Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block LH)
- -


OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.

Disconnect the G123 combination meter sub-assembly connector.


b.

Disconnect the 5D instrument panel junction block RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-13 (LR) - 5D-24 Always Below 1 Ω




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH
a.

Remove the instrument panel junction block RH.

U189991E02
2.031,0.125 2.365,0.292 0.333,0.167 10 false 5D 5.167,0.125 5.5,0.292 0.333,0.167 10 false 5G 3.51,1.5 3.844,1.667 0.333,0.167 10 false 5L


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5D-24 - 5L-1 Always Below 1 Ω
5D-24 - 5D-25 Always Below 1 Ω
5D-24 - 5G-17 Always Below 1 Ω



Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block RH)
- -


OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH

6.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the engine switch on (IG).


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).

Result:
Result Proceed to
Front turn signal light LH does not blink A
Rear turn signal light LH does not blink B




A

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK LH)

B

9.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK LH)
7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK LH)
a.

Disconnect the B29*1 or B22*2 headlight assembly LH (headlight cord LH) connector.


b.

Disconnect the 4L instrument panel junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B29-1 (B) - 4L-7*1 Always Below 1 Ω
B22-2 - 4L-7*2 Always Below 1 Ω
B29-3 (E) - Body ground*1 Always Below 1 Ω
B22-1 - Body ground*2 Always Below 1 Ω


HINT:

*1: for LED Headlight

*2: except LED Headlight




OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK LH
a.

Remove the instrument panel junction block LH.

U189992E02
1.948,0.167 2.281,0.333 0.333,0.167 10 false 4A 5.229,0.167 5.563,0.333 0.333,0.167 10 false 4L 0.188,0.073 0.521,0.24 0.333,0.167 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-14 - 4L-7 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block LH)
- -

Result:
Result Proceed to
OK (for LED Headlight) A
OK (except LED Headlight) B
NG C




A

REPLACE HEADLIGHT CORD LH (HEADLIGHT ASSEMBLY LH)

B

REPLACE HEADLIGHT ASSEMBLY LH (HEADLIGHT CORD LH)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

9.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK LH)
a.

Disconnect the M43 rear combination light assembly LH (rear turn signal light socket LH) connector.


b.

Disconnect the 4G instrument panel junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-4 - 4G-8 Always Below 1 Ω
M43-3 - Body ground Always Below 1 Ω




OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK LH
a.

Remove the instrument panel junction block LH.

U189998E02
1.927,0.198 2.26,0.365 0.333,0.167 10 false 4A 5.146,0.188 5.479,0.354 0.333,0.167 10 false 4G 0.188,0.073 0.521,0.24 0.333,0.167 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-14 - 4G-8 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block LH)
- -

Result:
Result Proceed to
OK (for LED Headlight) A
OK (except LED Headlight) B
NG C




A

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH (REAR TURN SIGNAL LIGHT SOCKET LH)

B

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH (REAR TURN SIGNAL LIGHT SOCKET LH)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

11.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the engine switch on (IG).


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).

Result:
Result Proceed to
Front turn signal light RH does not blink A
Rear turn signal light RH does not blink B




A

12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK RH)

B

14.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK RH)
12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.

Disconnect the B28*1 or B23*2 headlight assembly RH (headlight cord RH) connector.


b.

Disconnect the 5L instrument panel junction block RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B28-1 (B) - 5L-1*1 Always Below 1 Ω
B23-2 - 5L-1*2 Always Below 1 Ω
B28-3 (E) - Body ground*1 Always Below 1 Ω
B23-1 - Body ground*2 Always Below 1 Ω


HINT:

*1: for LED Headlight

*2: except LED Headlight




OK

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH
a.

Remove the instrument panel junction block RH.

U189999E02
2.073,0.208 2.406,0.375 0.333,0.167 10 false 5D 5.26,0.208 5.594,0.375 0.333,0.167 10 false 5L 0.198,0.052 0.531,0.219 0.333,0.167 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5D-24 - 5L-1 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block RH)
- -

Result:
Result Proceed to
OK (for LED Headlight) A
OK (except LED Headlight) B
NG C




A

REPLACE HEADLIGHT ASSEMBLY RH (HEADLIGHT CORD RH)

B

REPLACE HEADLIGHT ASSEMBLY RH (HEADLIGHT CORD RH)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH

14.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.

Disconnect the N45 rear combination light assembly RH (rear turn signal light socket RH) connector.


b.

Disconnect the 5G instrument panel junction block RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N45-4 - 5G-17 Always Below 1 Ω
N45-3 - Body ground Always Below 1 Ω




OK

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH
a.

Remove the instrument panel junction block RH.

U190000E02
1.865,0.188 2.198,0.354 0.333,0.167 10 false 5D 5.135,0.188 5.469,0.354 0.333,0.167 10 false 5G 0.167,0.073 0.5,0.24 0.333,0.167 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5D-24 - 5G-17 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block RH)
- -

Result:
Result Proceed to
OK (for LED Headlight) A
OK (except LED Headlight) B
NG C




A

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH (REAR TURN SIGNAL LIGHT SOCKET RH)

B

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH (REAR TURN SIGNAL LIGHT SOCKET RH)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH