Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2013.04–2016.05
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E236661E04
2.781,0.563 2.875,0.708 0.094,0.146 10 false 5 2.76,0.74 2.948,0.885 0.188,0.146 10 false j1 3.781,0.552 3.958,0.698 0.177,0.146 10 false 12 3.729,0.75 4.021,0.896 0.292,0.146 10 false G10 3.208,0.667 3.5,0.813 0.292,0.146 10 false IL+2 2.781,1.313 2.875,1.458 0.094,0.146 10 false 8 2.771,1.5 2.958,1.646 0.188,0.146 10 false j1 3.813,1.302 3.99,1.448 0.177,0.146 10 false 4 3.74,1.49 4.031,1.635 0.292,0.146 10 false G10 3.208,1.406 3.521,1.552 0.313,0.146 10 false EAU 2.896,1.865 3.865,2.271 0.969,0.406 10 false Spiral Cable Sub-assembly 0.896,1.104 1.094,1.25 0.198,0.146 10 false LH 0.896,1.854 1.115,2 0.219,0.146 10 false RH 0.427,2.5 2.354,2.646 1.927,0.146 10 false Steering Pad Switch Assembly 0.396,3.479 1.292,3.688 0.896,0.208 10 false from Battery 2.563,4.167 2.875,4.313 0.313,0.146 10 false TAIL 3.438,3.625 3.917,3.771 0.479,0.146 10 false PANEL 4.438,3.885 5.594,4.031 1.156,0.146 10 false to Main Body ECU 6.042,4.469 6.729,5.115 0.688,0.646 10 false Navigation Receiver Assembly 6,0.74 6.292,0.885 0.292,0.146 10 false ILL+ 5.677,0.552 5.854,0.698 0.177,0.146 10 false 10 5.625,0.74 5.896,0.906 0.271,0.167 10 false F13 6,1.51 6.396,1.656 0.396,0.146 10 false SWG 5.688,1.302 5.865,1.448 0.177,0.146 10 false 23 5.635,1.5 5.99,1.646 0.354,0.146 10 false F17

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the G10 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G10-12 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V




OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the j1 steering pad switch assembly connector.


b.

Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

U189963E02
0.125,0.073 0.333,0.281 0.208,0.208 10 false *a 4.813,0.302 5.063,0.479 0.25,0.177 10 false j1


c.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.



Text in Illustration
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Disconnect the j1 steering pad switch assembly connector.


b.

Disconnect the G10 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

E356085E03
1.292,0.75 1.708,1 0.417,0.25 5.469,1.25 5.885,1.5 0.417,0.25 0.979,1.26 1.271,1.385 false 1.542,1.552 2.021,1.406 false 5.979,1.698 6.167,1.406 false 5.219,2.073 5.708,1.906 false 0.135,0.115 0.573,0.396 0.438,0.281 10 false *a 1.448,0.781 1.76,0.979 0.313,0.198 10 false j1 0.667,1.156 1,1.354 0.333,0.198 10 false IL+2 2.063,1.313 2.375,1.51 0.313,0.198 10 false EAU 5.552,1.292 5.865,1.49 0.313,0.198 10 false G10 4.875,2.01 5.188,2.208 0.313,0.198 10 false EAU 6.198,1.313 6.531,1.51 0.333,0.198 10 false IL+2 0.729,0.74 1.167,1.021 0.438,0.281 10 false *b 4.875,1.198 5.313,1.479 0.438,0.281 10 false *c

Standard Resistance:
Tester Connection Condition Specified Condition
j1-5 (IL+2) - G10-12 (IL+2) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
j1-8 (EAU) - G10-4 (EAU) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-5 (IL+2) - G10-12 (IL+2) Always Below 1 Ω
j1-8 (EAU) - G10-4 (EAU) Always Below 1 Ω


NOTICE:
·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



HINT:


Text in Illustration
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the G10 spiral cable sub-assembly connector.


b.

Disconnect the F17 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-4 (EAU) - F17-23 (SWG) Always Below 1 Ω
G10-4 (EAU) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the F13 navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F13-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR