Home › Vehicle Interior › WINDOW / GLASS › BACK DOOR GLASS › from 2016.05
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292223 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 64819 1.INSTALL BACK WINDOW GLASS NO. 2 SPACER

B140668E01
0.039,0 0.889,0.202 0.850,0.202 10 Backside: 0.119,1.691 0.983,2.291 0.864,0.600 10 Marking for spacer pasting 1.013,1.983 1.976,2.31 false

a.

Apply Primer G to the installation part of the clips.

HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.



b.

Install 2 new spacers onto the glass as shown in the illustration.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




Hide 64828 2.INSTALL BACK WINDOW GLASS CLIP

a.

Apply Primer G to the installation part of the clips.

HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.



b.
B140667E05
0.833,0.688 1.906,0.969 false 0.125,0.083 0.979,0.281 0.854,0.198 10 false Backside: 0.104,0.427 0.969,1.031 0.865,0.604 10 false Marking for spacer pasting

Install 2 new clips onto the glass as shown in the illustration.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




Hide 75574B 3.INSTALL BACK WINDOW MOULDING OUTSIDE

B140669E02
0.037,0.041 0.859,0.280 0.823,0.239 10 Backside: 0.574,0.905 0.831,1.162 0.258,0.258 10 A 0.995,1.02 1.253,1.278 0.258,0.258 10 A 3.517,1.558 3.775,1.816 0.258,0.258 10 A 3.912,1.492 4.170,1.750 0.258,0.258 10 A 1.687,1.769 1.862,2.017 0.174,0.248 10 B 1.685,2.156 1.931,2.372 0.246,0.216 10 B 4.616,0.202 5.085,0.409 0.469,0.207 10 A - A 4.618,1.474 5.087,1.663 0.469,0.189 10 B - B 5.606,0.979 5.849,1.181 0.244,0.202 10 a 5.728,2.276 5.966,2.421 0.239,0.145 10 b

a.

Apply Primer G to the installation part of the window moulding.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install a new moulding as shown in the illustration.

Standard measurement:
Area Specified Condition
a 10.5 mm (0.413 n.)
b 7.2 mm (0.283 in.)



Hide 68131 4.INSTALL BACK DOOR GLASS

B145155E03
1.99,0.854 2.406,1.125 false 1.875,2 2.375,2.146 false 1.656,2.417 2.302,2.292 false 1.344,0.74 1.948,0.938 0.604,0.198 10 false Primer M 1.25,1.917 1.854,2.115 0.604,0.198 10 false Primer M 0.573,4.385 1.354,4.552 0.781,0.167 10 false Primer M 1.031,2.333 1.729,2.531 0.698,0.198 10 false Adhesive 1.479,0.24 2.323,0.438 0.844,0.198 10 false CORRECT 2.208,2.396 3.063,2.625 0.854,0.229 10 true INCORRECT

a.

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

B145159E04
2.594,1.885 2.594,2.26 false 4.073,0.771 3.938,0.938 false 6.135,0.792 6.01,0.938 false 4.229,2.063 4.073,2.229 false 0.094,0.063 0.917,0.302 0.823,0.24 10 false Backside: 1.771,0.833 1.927,1 0.156,0.167 10 false A 1.771,1.198 1.927,1.365 0.156,0.167 10 false A 0.302,1.021 0.458,1.188 0.156,0.167 10 false B 0.615,1.135 0.771,1.302 0.156,0.167 10 false B 2.667,1.177 2.823,1.344 0.156,0.167 10 false B 2.969,1.104 3.125,1.271 0.156,0.167 10 false B 1.583,1.667 1.74,1.833 0.156,0.167 10 false C 1.573,2.01 1.729,2.177 0.156,0.167 10 false C 1.844,2.292 3.354,2.5 1.51,0.208 10 false Adhesive Center Line 3.563,0.969 5.073,1.177 1.51,0.208 10 false Adhesive Center Line 5.417,0.969 6.927,1.177 1.51,0.208 10 false Adhesive Center Line 3.573,2.271 5.083,2.479 1.51,0.208 10 false Adhesive Center Line 0.74,2.396 1.406,2.604 0.667,0.208 10 false Primer G 3.49,0.198 3.854,0.365 0.365,0.167 10 false A - A 5.365,0.188 5.729,0.354 0.365,0.167 10 false B - B 3.49,1.49 3.854,1.656 0.365,0.167 10 false C - C 3.979,0.344 4.083,0.51 0.104,0.167 10 false a 6.448,0.51 6.552,0.677 0.104,0.167 10 false a 5.948,0.26 6.052,0.417 0.104,0.156 10 false b 5.958,0.646 6.146,0.823 0.188,0.177 10 false c 4.021,1.646 4.208,1.823 0.188,0.177 10 false c

Standard measurement:
Area Specified Condition
a 5.0 mm (0.198 in.)
b 15.5 mm (0.615 in.)
c 13.7 mm (0.543 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent


i.

Cut off the tip of the cartridge nozzle as shown in the illustration below.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage time frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass as shown in the illustration.

B145169E04
2.375,1.938 2.375,2.313 false 4.646,0.885 4.458,1.031 false 4.833,2.156 4.688,2.323 false 6.458,0.875 6.24,1.052 false 0.094,0.063 0.906,0.25 0.813,0.188 10 true Backside: 2.781,0.938 2.938,1.104 0.156,0.167 10 false A 2.792,1.24 2.948,1.406 0.156,0.167 10 false A 1.479,1.177 1.635,1.344 0.156,0.167 10 false B 3.917,1.208 4.073,1.375 0.156,0.167 10 false B 1.771,1.25 1.927,1.417 0.156,0.167 10 false B 3.625,1.25 3.781,1.417 0.156,0.167 10 false B 2.635,2 2.792,2.167 0.156,0.167 10 false C 2.635,1.698 2.792,1.865 0.156,0.167 10 false C 2.26,2.333 3.771,2.542 1.51,0.208 10 false Adhesive Center Line 5.677,1.052 7.031,1.219 1.354,0.167 10 false Adhesive Center Line 4.188,2.323 5.656,2.469 1.469,0.146 10 false Adhesive Center Line 4.167,1.031 5.635,1.188 1.469,0.156 10 false Adhesive Center Line 1.365,2.281 2.031,2.49 0.667,0.208 10 false Primer G 4.198,0.219 4.563,0.385 0.365,0.167 10 false A - A 5.688,0.229 6.052,0.396 0.365,0.167 10 false B - B 4.177,1.51 4.542,1.677 0.365,0.167 10 false C - C 0.521,2.26 0.667,2.417 0.146,0.156 10 false a 0.354,1.333 0.5,1.49 0.146,0.156 10 false a 0.896,1.844 1,2 0.104,0.156 10 false b 0.813,1.552 0.917,1.708 0.104,0.156 10 false b 4.563,0.333 4.75,0.51 0.188,0.177 10 false c 6.729,0.469 6.917,0.646 0.188,0.177 10 false c 6.229,0.219 6.385,0.375 0.156,0.156 10 false d 4.635,1.635 4.792,1.792 0.156,0.156 10 false e

Standard measurement:
Area Specified Condition
a 8.0 mm (0.315 in.)
b 12.0 mm (0.472 in.)
c 5.0 mm (0.198 in.)
d 15.5 mm (0.615 in.)
e 13.7 mm (0.543 in.)




d.

Install the back door glass to the vehicle body.

i.

Hold the back window glass securely in place with tape or equivalent until the adhesive has hardened.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




ii.

Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.


iii.
BO03986E34
1.094,1.646 1.594,1.813 false 1.625,1.75 2.323,1.948 0.698,0.198 10 false Adhesive

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive onto the glass rim.


NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum time:
Temperature Minimum time prior to driving vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



iv.
B145072

Install the defogger wire with the nut and 2 clamps.


v.

Connect the 2 connectors.



Hide 76801 5.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 81580D 7.INSTALL REAR LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 84280D 8.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

Hide 84270G 9.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 85110R 11.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 85110R 12.INSTALL REAR WIPER MOTOR GROMMET

Hide 85190R 13.INSTALL REAR WIPER ARM ASSEMBLY

Hide 67751 14.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

Hide 62581H 15.INSTALL REAR WINDOW SIDE GARNISH RH

Hide 62582H 16.INSTALL REAR WINDOW SIDE GARNISH LH

Hide 67848 17.INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

Hide 67939D 18.INSTALL BACK DOOR CENTER GARNISH

Hide 68131 19.CHECK FOR LEAKS AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 28800 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 28800 21.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.