Home › Vehicle Interior › INTERIOR PANEL › LOWER INSTRUMENT PANEL › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059594 INTERIOR PANEL _0292234 LOWER INSTRUMENT PANEL A

INTERIOR PANEL  LOWER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 1. TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.

B462521E01
0.135,1.156 0.479,1.354 0.344,0.198 10 false Code 2.458,1.156 2.802,1.354 0.344,0.198 10 false Code 4.75,1.156 5.094,1.354 0.344,0.198 10 false Code 1.125,1.146 1.542,1.354 0.417,0.208 10 false Shape 3.5,1.146 3.917,1.354 0.417,0.208 10 false Shape 5.792,1.156 6.208,1.365 0.417,0.208 10 false Shape 0.229,1.927 0.438,2.167 0.208,0.24 10 false A 4.875,1.938 5.083,2.177 0.208,0.24 10 false C 2.542,1.938 2.75,2.177 0.208,0.24 10 false B 0.25,3.125 0.458,3.365 0.208,0.24 10 false D 2.542,3.125 2.75,3.365 0.208,0.24 10 false E 4.865,3.125 5.073,3.365 0.208,0.24 10 false F 0.229,4.26 0.438,4.5 0.208,0.24 10 false G 2.531,4.26 2.74,4.5 0.208,0.24 10 false H 4.896,4.26 5.104,4.5 0.208,0.24 10 false I 1.938,1.677 2.417,2.427 0.479,0.75 10 false φ=5 (0.20) L=15 (0.59) 4.292,1.698 4.771,2.448 0.479,0.75 10 false φ=8 (0.31) L=19 (0.75) 6.521,1.708 7,2.458 0.479,0.75 10 false φ=5 (0.20) L=16 (0.63) 1.927,2.844 2.406,3.594 0.479,0.75 10 false φ=6 (0.24) L=20 (0.79) 4.26,2.833 4.74,3.583 0.479,0.75 10 false φ=5 (0.20) L=14 (0.55) 6.573,2.99 6.99,3.438 0.417,0.448 10 false φ=6 (0.24) 1.927,3.938 2.406,4.688 0.479,0.75 10 false φ=6 (0.24) L=20 (0.79) 4.26,3.927 4.74,4.677 0.479,0.75 10 false φ=5 (0.20) L=14 (0.55) 6.563,3.927 7.042,4.677 0.479,0.75 10 false φ=5 (0.20) L=16 (0.63) 5.719,0.563 7.031,0.792 1.313,0.229 10 false mm (in.) (L=Length)


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 83100 3.REMOVE COMBINATION METER ASSEMBLY

Hide 55302A 4.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 33504F 5.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

a.
B323099

Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.


Hide 67914B 6.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913B 7.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 9.REMOVE COWL SIDE TRIM BOARD RH

Hide 55607 10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B143406E05
0.271,2.781 0.688,2.969 0.417,0.188 10 true Claw 0.292,3.042 0.708,3.229 0.417,0.188 10 false Guide

Disengage the 2 claws and 2 guides, and remove the No. 2 instrument panel under cover sub-assembly.


Hide 55550 11.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.

Open the glove compartment door.


b.
B146514E03
0.583,2.208 1.104,2.208 1.104,2.208 1.802,2.833 false 0.198,2.115 0.521,2.292 0.323,0.177 10 true Claw

Disengage the claw from the glove compartment door stopper.


c.
B146515E02
0.604,1.094 0.292,1.302 0.292,1.302 0.292,1.896 true 2.75,1.042 3.063,1.25 3.063,1.25 3.063,1.844 true 2.833,1.906 3.333,2.083 0.5,0.177 10 true Stopper 0.104,1.906 0.604,2.083 0.5,0.177 10 true Stopper 0.854,1.156 1.01,1.344 0.156,0.188 10 false B 2.396,1.125 2.552,1.313 0.156,0.188 10 false A

Insert a finger into part A and bend the part in the direction indicated by the arrow in the illustration to disengage the stopper.


d.

Insert a finger into part B and bend the part in the direction indicated by the arrow in the illustration to disengage the stopper. Lower the glove compartment door assembly until the front of the door is level.


e.
B143398E05
0.271,4.26 0.708,4.458 0.438,0.198 10 false Hinge

Pull the glove compartment door assembly horizontally toward the rear of the vehicle to disengage the 2 hinges. Remove the glove compartment door assembly.

NOTICE:

Pulling the compartment door upward to remove it causes the hinges to be deformed when reinstalling the door. Be sure to pull out the compartment door horizontally to remove it.



Hide 89340A 12.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar)

Hide 55474B 13.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B462642

Disengage the 13 claws.


b.

Disconnect the connector and remove the instrument cluster finish panel garnish.


Hide 55447C 14.REMOVE NO. 1 SWITCH HOLE BASE

a.
B462643

Disengage the 5 claws.


b.

Disconnect each connector and remove the No. 1 switch hole base.


Hide 55606 15.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B146594

Remove the screw.


b.

Disengage the 2 claws and remove the No. 1 instrument panel under cover sub- assembly.


Hide 55432B 16.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/o Knee Airbag)

a.
B462644

Remove the 3 screws and disengage the 8 claws.


b.

Disconnect the hood lock control lever cable and fuel lid open lever cable.


c.

Remove the duct from the room temperature sensor.


d.

Disconnect each connector and remove the instrument panel finish panel lower.


Hide 55432B 17.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/ Knee Airbag)

a.
B462645

Remove the 3 screws and Disengage the 13 claws.


b.

Disconnect the hood lock control lever cable and fuel lid open lever cable.


c.

Remove the duct from the room temperature sensor.


d.

Disconnect each connector and remove the instrument panel finish panel lower.


Hide 58533C 18.REMOVE FLOOR CARPET COVER CENTER RH

a.
B462646

Disengage the claw.


b.

Disengage the 5 claws and remove the floor carpet cover center RH.


Hide 58534E 19.REMOVE FLOOR CARPET COVER CENTER LH

a.
B462647

Disengage the 2 clips.


b.

Disengage the 2 claws and remove the floor carpet cover center LH.


Hide 55434B 20.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER

a.
B272189E02
0.354,3.104 0.833,3.271 0.479,0.167 10 false Clamp

Remove the bolt.


b.

Disengage the 3 clamps.


c.
B272192

Disengage the 3 claws as shown in the illustration.


d.
B272194

Disengage the 3 claws as shown in the illustration.


e.
B272196

Disengage the 3 claws and remove the instrument panel finish panel lower center as shown in the illustration.


Hide 55433B 21.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL LOWER

a.
B462648

Disengage the 4 claws and remove the No. 2 instrument panel finish panel lower.


Hide 55900A 22.REMOVE HEATER CONTROL AND ACCESSORY

a.
B144508

Disengage the 6 claws.


b.

Disconnect each connector and remove the heater control and accessory.


Hide 55400 25.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (w/o Knee Airbag)

a.
B144510

Remove the bolt and instrument panel safety pad assembly.


Hide 55312 27.REMOVE INSTRUMENT PANEL LOWER

a.

Remove the 3 bolts, 11 screws and 4 nuts.

B144512E01
0.215,6.489 0.578,6.663 0.363,0.174 10 Claw 0.213,6.224 0.642,6.412 0.429,0.188 10 Clamp


b.

Disconnect each connector and each clamp.


c.

Disengage the 2 claws and remove the instrument panel lower.

B462649