P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)
Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010
Also covers:
- P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1)
- P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)
- P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2)
Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014
DESCRIPTION
The VVT (Variable Valve Timing) system includes the ECM, Camshaft Timing Oil Control Valve (OCV) Assembly and camshaft timing gear assembly. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the camshaft timing gear assembly. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV, based on the signals transmitted by several sensors. The camshaft timing gear assembly regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0011 P0021 |
Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic) |
|
| P0012 P0022 |
Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic) |
|
MONITOR DESCRIPTION
- The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, Camshaft Timing Oil Control Valve (OCV) Assembly and camshaft timing gear assembly. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the camshaft timing gear assembly. The camshaft timing gear assembly can advance or retard the intake camshaft.
- If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the camshaft timing gear assembly stuck malfunction and stores a DTC.
WIRING DIAGRAM
Refer to DTC P0010 (Click here).INSPECTION PROCEDURE
- HINT:
- DTC P0011, P0012, P0021 or P0022 may be set when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain set even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.
- HINT:
Abnormal Bank
Advanced Timing Over
(Valve Timing is Out of Specified Range)
Retarded Timing Over
(Valve Timing is Out of Specified Range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022
- If DTC P0011 or P0012 is displayed, check the VVT system for intake camshaft circuit (for Bank 1).
- Bank 1 refers to the bank that includes No. 1 cylinder.
- If DTC P0021 or P0022 is displayed, check the VVT system for intake camshaft circuit (for Bank 2).
- Bank 2 refers to the bank that does not include No. 1 cylinder.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- If DTC P0011 or P0012 is displayed, check the VVT system for intake camshaft circuit (for Bank 1).
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P0011, P0012, P0021 or P0022 is output
A
P0011, P0012, P0021 or P0022 and other DTCs are output
B
- HINT:
- If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
- OK:
Tester Operation
Specified Condition
OCV OFF
Normal engine speed
OCV ON
Soon after OCV switched from OFF to ON, engine idles roughly or stalls
|
|
||||
| OK | |
| 3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Read DTCs using the tester.
- OK:
- No DTC output.
|
|
||||
| OK | ||
| ||
| 4. CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING CHAIN) |
![]() ![]() |
Remove the cylinder head cover LH and RH.
Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.
Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.
- Text in Illustration:
*1
Alignment Mark
- OK:
- Alignment marks on camshaft timing gears are aligned as shown in the illustration.
|
|
||||
| OK | |
| 5. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV FOR INTAKE CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for intake side) (Click here).
|
|
||||
| OK | |
| 6. INSPECT OIL CONTROL VALVE FILTER (OCV FILTER FOR BANK 1 OR BANK 2) |
Remove the OCV filter (Click here).
Check that the filter is not clogged.
- OK:
- Filter is not clogged.
|
|
||||
| OK | |
| 7. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Inspect the camshaft timing gear assembly (Click here).
|
|
||||
| OK | |
| 8. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Read the output DTCs using the tester.
- OK:
- No DTC is output.
- HINT:
- DTC P0011, P0012, P0021 or P0022 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.
|
|
||||
| OK | ||
| ||

