2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Door Courtesy Switch Circuit

Circuit diagnosis · Vehicles built Aug 2008 – Oct 2010

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014

DESCRIPTION

The main body ECU detects the condition of each door courtesy switch.

WIRING DIAGRAM

E174658E01
E174659E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Body / Data List /

  1. According to the display on tester, read the "Data List".

    Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver door courtesy switch signal/ON or OFF
    ON :Driver door open
    OFF: Driver door closed
    -
    P Door Courtesy SW
    Front passenger door courtesy switch signal/ON or OFF
    ON: Front passenger door open
    OFF: Front passenger door closed
    -
    Rear Door Courtesy SW
    Rear door courtesy switch signal/ON or OFF
    ON: Either right or left door open
    OFF: Both the right and left rear doors are closed
    -
    Luggage Courtesy SW
    Back door and back window courtesy switch signal/ON or OFF
    ON: Either back door or back window open
    OFF: Both back door and back window closed
    -

    OK:
    Condition sign can be displayed.

    Result:
    Result
    Proceed to
    OK
    A
    Driver side door courtesy switch does not operate
    B
    Front passenger side door courtesy switch does not operate
    C
    Both rear door courtesy switches do not operate
    D
    Back door courtesy switch or back window courtesy switch does not operate
    E



B
Go to step 2

C
Go to step 4

D
Go to step 6

E
Go to step 8
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT DOOR COURTESY SWITCH (DRIVER SIDE)
  1. Inspect the door courtesy switch (Click here).

    OK:
    Door courtesy switch is normal.



NG
REPLACE DOOR COURTESY SWITCH (DRIVER SIDE) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (DOOR COURTESY SWITCH (DRIVER SIDE) - MAIN BODY ECU)

  1. B204342E01
    Disconnect the E7 main body ECU connector.

  1. Disconnect the J1 door courtesy switch connector.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-23 (DCTY) - J1-1
    Always
    Below 1 Ω
    E7-23 (DCTY) or J1-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the door courtesy switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

4. INSPECT DOOR COURTESY SWITCH (FRONT PASSENGER SIDE)
  1. Inspect the door courtesy switch (Click here).

    OK:
    Door courtesy switch is normal.



NG
REPLACE DOOR COURTESY SWITCH (FRONT PASSENGER SIDE) (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (DOOR COURTESY SWITCH (FRONT PASSENGER SIDE) - MAIN BODY ECU)

  1. B204342E02
    Disconnect the E7 main body ECU connector.

  1. Disconnect the I1 door courtesy switch connector.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-24 (PCTY) - I1-1
    Always
    Below 1 Ω
    E7-24 (PCTY) or I1-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the door courtesy switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

6. INSPECT REAR DOOR COURTESY SWITCH (REAR LH UPPER, REAR LH LOWER, REAR RH UPPER, REAR RH LOWER)
  1. Inspect the rear door lock upper assembly (Click here).

  1. Inspect the rear door lock lower assembly (Click here).

OK:
Door courtesy switch is normal.

Result:
Result
Proceed to
OK
A
NG (Rear door lock upper assembly)
B
NG (Rear door lock lower assembly)
C



B
REPLACE REAR DOOR LOCK UPPER ASSEMBLY (REAR DOOR COURTESY SWITCH) (Click here)

C
REPLACE REAR DOOR LOCK LOWER ASSEMBLY (REAR DOOR COURTESY SWITCH) (Click here)
A


7. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY SWITCH - MAIN BODY ECU)

  1. B204343E01
    Disconnect the E7 main body ECU connector.

  1. Disconnect the J2, J3, I2 and I3 door courtesy switch connectors.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    LH 
    Tester Connection
    Condition
    Specified Condition
    E7-11 (RLCY) - J2-2
    Always
    Below 1 Ω
    E7-11 (RLCY) or J2-2 - Body ground
    Always
    10 kΩ or higher
    J2-1 - Body ground
    Always
    Below 1 Ω
    E7-11 (RLCY) - J3-1
    Always
    Below 1 Ω
    E7-11 (RLCY) or J3-1 - Body ground
    Always
    10 kΩ or higher
    J3-2 - Body ground
    Always
    Below 1 Ω
    RH 
    Tester Connection
    Condition
    Specified Condition
    E7-12 (RRCY) - I2-2
    Always
    Below 1 Ω
    E7-12 (RRCY) or I2-2 - Body ground
    Always
    10 kΩ or higher
    I2-1 - Body ground
    Always
    Below 1 Ω
    E7-12 (RRCY) - I3-1
    Always
    Below 1 Ω
    E7-12 (RRCY) or I3-1 - Body ground
    Always
    10 kΩ or higher
    I3-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the main body ECU connector.

  1. Reconnect the door courtesy switch connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

8. INSPECT BACK DOOR COURTESY SWITCH
  1. Inspect the door courtesy switch (Click here).

    OK:
    Door courtesy switch is normal.



NG
REPLACE BACK DOOR COURTESY SWITCH (Click here)
OK


9. INSPECT BACK WINDOW LOCK ASSEMBLY (BACK WINDOW COURTESY SWITCH)
  1. Inspect the door courtesy switch (Click here).

    OK:
    Door courtesy switch is normal.



NG
REPLACE BACK WINDOW LOCK ASSEMBLY (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (BACK DOOR COURTESY, BACK WINDOW COURTESY - MAIN BODY ECU)

  1. B204344E01
    Disconnect the E7 main body ECU connector.

  1. Disconnect the S6 back window lock assembly connector.

  1. Disconnect the L2 back door courtesy switch connector.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-7 (BCTY) - S6-2
    Always
    Below 1 Ω
    E7-7 (BCTY) or S6-2 - Body ground
    Always
    10 kΩ or higher
    S6-1 - Body ground
    Always
    Below 1 Ω
    E7-7 (BCTY) - L2-1
    Always
    Below 1 Ω
    E7-7 (BCTY) or L2-1 - Body ground
    Always
    10 kΩ or higher

    HINT:
    The circuit has diodes, so reverse the two leads and check again.

  1. Reconnect the main body ECU connector.

  1. Reconnect the back door courtesy switch connector.

  1. Reconnect the back window lock assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Door Courtesy Switch Circuit (Jul 2007 – Jul 2008)Door Courtesy Switch Circuit (Nov 2010 – Jul 2011) →