2011-2016 FJ Cruiser · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built Dec 2007 – Jul 2009

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM constantly generates 5 V power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A116143E09
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A173383E01

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.

    OK:
    MIL lights up



OK
SYSTEM OK
NG


2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Check the communication between an intelligent tester and ECM.

    Result:
    Result
    Proceed To
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3. CHECK MIL (THROTTLE WITH MOTOR BODY ASSEMBLY)
  1. Disconnect the throttle with motor body connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle with motor body connector.



A
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
B


4. CHECK MIL (ACCELERATOR PEDAL ROD ASSEMBLY)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (Click here)
B


5. CHECK MIL (VVT SENSOR FOR BANK 1)
  1. Disconnect the VVT sensor (bank 1) connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor connector.



A
REPLACE VVT SENSOR FOR BANK 1 (Click here)
B


6. CHECK MIL (VVT SENSOR FOR BANK 2)
  1. Disconnect the VVT sensor (bank 2) connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor connector.



A
REPLACE VVT SENSOR FOR BANK 2 (Click here)
B


7. CHECK HARNESS AND CONNECTOR (VC OUTPUT CIRCUIT)
  1. Disconnect the throttle body connector.

  1. Disconnect the accelerator pedal connector.

  1. A115981E02
    Disconnect the ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    VC (B1-23) - Body ground
    10 kΩ or higher
    VCPA (E47-26) - Body ground
    VCP2 (E47-27) - Body ground

  1. Reconnect the throttle body connector.

  1. Reconnect the accelerator pedal connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← VC Output Circuit (Jul 2007 – Nov 2007)VC Output Circuit (Aug 2009 – Oct 2010) →