2011-2016 FJ Cruiser · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM constantly generates 5 V power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A227200E01
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A226177E01

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    OK:
    MIL lights up



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Check the communication between the intelligent tester and ECM.

    Result 
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3. CHECK MIL (THROTTLE WITH MOTOR BODY ASSEMBLY)
  1. Disconnect the throttle with motor body assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE THROTTLE BODY ASSEMBLY (Click here)
A


4. CHECK MIL (ACCELERATOR PEDAL ROD ASSEMBLY)
  1. Disconnect the accelerator pedal connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)
A


5. CHECK MIL (VVT SENSOR (FOR INTAKE SIDE OF BANK 1))
  1. Disconnect the VVT sensor (for intake side of bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 1) (Click here)
A


6. CHECK MIL (VVT SENSOR (FOR INTAKE SIDE OF BANK 2))
  1. Disconnect the VVT sensor (for intake side of bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 2) (Click here)
A


7. CHECK MIL (VVT SENSOR (FOR EXHAUST SIDE OF BANK 1))
  1. Disconnect the VVT sensor (for exhaust side of bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 1) (Click here)
A


8. CHECK MIL (VVT SENSOR (FOR EXHAUST SIDE OF BANK 2))
  1. Disconnect the VVT sensor (for exhaust side of bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 2) (Click here)
A


9. CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)
  1. Disconnect the power steering oil pressure switch (sensor) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE POWER STEERING OIL PRESSURE SWITCH (Click here)
A


10. CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle with motor body assembly connector.

  1. Disconnect the accelerator pedal rod assembly connector.

  1. Disconnect the VVT sensor (for intake side of bank 1) connector.

  1. Disconnect the VVT sensor (for intake side of bank 2) connector.

  1. Disconnect the VVT sensor (for exhaust side of bank 1) connector.

  1. Disconnect the VVT sensor (for exhaust side of bank 2) connector.

  1. Disconnect the power steering oil pressure switch (sensor) connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (check for short):
    Tester Connection
    Condition
    Specified Condition
    B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher
    E81-4 (VCPA) - Body ground
    Always
    10 kΩ or higher
    E81-2 (VCP2) - Body ground
    Always
    10 kΩ or higher
    B49-13 (VCTA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← VC Output Circuit (Dec 2007 – Jul 2009)VC Output Circuit (Nov 2010 – Jul 2014) →