2011-2016 FJ Cruiser · Service Manual BRAKE

C1251 Open in Pump Motor Circuit

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.
DTC Code
DTC Detection Condition
Trouble Area
C1251
Open in motor system circuit (motor input circuit)
  1. Pump motor wire harness connection
  2. Brake booster with accumulator pump assembly
  3. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

C230320E02

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Remove the hydraulic brake booster before the inspection (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    Motor relay
    Relay ON/OFF
    An operating sound of the motor can be heard.

  1. Check the operating sound of the motor individually when operating it with the tester.

    OK:
    An operating sound of the motor can be heard.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

3. CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS
  1. Remove the hydraulic brake booster assembly (Click here).

  1. Check the tightening torque of the 2 screws which secure the wire harness connecting the master cylinder solenoid and brake booster with accumulator pump assembly.

OK:
The harness is tightened to the specified torque.

Torque:
2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



NG
RETIGHTEN SCREWS
OK


4. CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS

  1. F052356E04
    Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Red wire terminal - Black wire terminal
    Always
    Below 2 Ω

    Text in Illustration 
    *1
    Pump motor wire harness
    *a
    Red wire
    *b
    Black wire



NG
REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY (Click here)
OK


5. RECONFIRM DTC
  1. Reassemble the hydraulic brake booster assembly (Click here).

  1. Install the hydraulic brake booster assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1251 Open in Pump Motor Circuit (Nov 2010 – Jul 2012)C1251/51 Open in Pump Motor Circuit (Jul 2007 – Oct 2010) →