2011-2016 FJ Cruiser · Service Manual SECURITIES

B2780 Push Switch / Key Unlock Warning Switch Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

This DTC will be output if the transponder key ECU does not detect that the unlock warning switch is ON even when the ignition switch is in the ON position. Under normal conditions, the unlock warning switch is ON when the ignition switch is in the ON position.
DTC No.
DTC Detection Condition
Trouble Area
B2780
"Unlock warning switch ON" is not detected when ignition switch is ON
  1. Wire harness
  2. Unlock warning switch
  3. Transponder key ECU

WIRING DIAGRAM

B261043E05

INSPECTION PROCEDURE

NOTICE:
If the transponder key ECU is replaced, register the key and ECU communication ID.


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Immobiliser / Data List.

  1. According to the display on the intelligent tester, read the Data List.

Immobiliser 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key SW
Unlock warning switch signal/ON or OFF
ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-

OK:
ON (Key is in ignition key cylinder) appears on the screen.



NG
Go to step 2
OK

REPLACE TRANSPONDER KEY ECU

2. INSPECT UNLOCK WARNING SWITCH
  1. Inspect the unlock warning switch.

    HINT:
    1. for LHD: (Click here)
    2. for RHD: (Click here)

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE UNLOCK WARNING SWITCH (Click here)

C
REPLACE UNLOCK WARNING SWITCH (Click here)
A


3. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - BODY GROUND)

  1. B175505E02
    for LHD
    1. Disconnect the E21 unlock warning switch connector.

  1. for RHD

    1. Disconnect the E90 unlock warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E21-1 - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E90-1 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Unlock Warning Switch)

  1. Reconnect the unlock warning switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - UNLOCK WARNING SWITCH)
  1. Disconnect the E80 transponder key ECU connector.

  1. for LHD

    1. Disconnect the E21 unlock warning switch connector.

  1. for RHD

    1. Disconnect the E90 unlock warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E80-3 (KSW) - E21-2
    Always
    Below 1 Ω
    E21-2 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E80-3 (KSW) - E90-2
    Always
    Below 1 Ω
    E90-2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the unlock warning switch connector.

  1. Reconnect the transponder key ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU


← B2780 Push Switch / Key Unlock Warning Switch Malfunction (Aug 2009 – Oct 2010)B2784 Antenna Coil Open / Short (Jul 2007 – Jul 2009) →