C1415 Rear Speed Sensor RH Output Malfunction
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Also covers:
- C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1416 Rear Speed Sensor LH Output Malfunction
Versions by build date: Nov 2010 – Jul 2012 from Aug 2012
DESCRIPTION
Refer to DTCs C1401 and C1402 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1415 C1416 |
One of the following conditions is met:
|
|
| C1277 C1278 |
Stored only during test mode. |
|
- HINT:
- DTCs C1415 and C1277 are for the rear speed sensor RH.
- DTCs C1416 and C1278 are for the rear speed sensor LH.
- DTCs C1415 and C1277 are for the rear speed sensor RH.
WIRING DIAGRAM
Refer to DTCs C1407 and C1408 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
- Check the speed sensor signal after cleaning or replacement (Click here).
- When replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Speed Open
Rear speed sensor RH open detection/ Error or Normal
Normal
-
RL Speed Open
Rear speed sensor LH open detection/ Error or Normal
Normal
-
- OK:
- Normal (there are no momentary interruptions).
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RL Wheel Speed
Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check that there is no difference between the speed value output from the speed sensor displayed on the tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 3. PERFORM TEST MODE (SIGNAL CHECK) |
Perform the signal check in the Test Mode Procedure (Click here).
- OK:
- All test mode DTCs are cleared.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTCs C1415 and C1416 are not output
A
DTCs C1415 and/or C1416 are output
B
|
|
||||
| A | ||
| ||
| 5. CHECK REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation.

- OK:
- There is no clearance between the sensor and the rear axle.
The installation nut is tightened properly.
- Torque:
- 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Text in Illustration *1
Rear Speed Sensor
*a
No clearance
*b
OK
*c
NG
|
|
||||
| OK | |
| 6. INSPECT REAR SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 7. INSPECT REAR SPEED SENSOR ROTOR |
Remove the rear axle hub and bearing assembly (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- HINT:
- The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.
|
|
||||
| OK | |
| 8. INSPECT SKID CONTROL SENSOR WIRE |


| *1 |
Skid Control Sensor Wire |
- |
- |
| *a |
for RH |
*b |
for LH |
Remove the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
OX1-4 - X1-2 (RR+)
Always
Below 1 Ω
OX1-3 - X1-1 (RR-)
Always
Below 1 Ω
OX1-4 - OX1-3
Always
10 kΩ or higher
OX1-4 - OX1-1
Always
10 kΩ or higher
OX1-4 - OX1-2
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
OX1-2 - X2-2 (RL+)
Always
Below 1 Ω
OX1-1 - X2-1 (RL-)
Always
Below 1 Ω
OX1-2 - OX1-1
Always
10 kΩ or higher
OX1-2 - OX1-3
Always
10 kΩ or higher
OX1-2 - OX1-4
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Install the skid control sensor wire.
Disconnect the A4 skid control ECU connector.
Disconnect the X1 and/or X2 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
A4-5 (RR+) - X1-2 (RR+)
Always
Below 1 Ω
A4-5 (RR+) - Body ground
Always
10 kΩ or higher
A4-19 (RR-) - X1-1 (RR-)
Always
Below 1 Ω
A4-19 (RR-) - Body ground
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
A4-20 (RL+) - X2-2 (RL+)
Always
Below 1 Ω
A4-20 (RL+) - Body ground
Always
10 kΩ or higher
A4-6 (RL-) - X2-1 (RL-)
Always
Below 1 Ω
A4-6 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 10. CHECK TERMINAL VOLTAGE (RR+, RL+) |
Disconnect the X1 and/or X2 rear speed sensor connector.
Connect the A4 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
for RH Tester Connection
Switch Condition
Specified Condition
X1-2 (RR+) - Body ground
Ignition switch ON
11 to 14 V
for LH Tester Connection
Switch Condition
Specified Condition
X2-2 (RL+) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Rear Speed Sensor)
*b
for RH
*c
for LH
|
|
||||
| OK | |
| 11. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTCs C1415 and C1416 are not output
A
DTCs C1415 and/or C1416 are output
B
|
|
||||
| A | ||
| ||
| 12. REPLACE REAR SPEED SENSOR |
Replace the rear speed sensor (Click here).
| NEXT | |
| 13. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTCs C1415 and C1416 are not output
A
DTCs C1415 and/or C1416 are output
B
|
|
||||
| A | ||
| ||
