2011-2016 FJ Cruiser · Service Manual BRAKE

C1413 Front Speed Sensor RH Output Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2012

Also covers:

Versions by build date: Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1413
C1414
One of the following conditions is met:
  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Front speed sensor RH/LH
  2. Skid control sensor wire
  3. Speed sensor circuit
  4. Speed sensor rotor RH/LH
  5. Master cylinder solenoid (Skid control ECU)
C1275
C1276
Stored only during test mode.
  1. Front speed sensor RH/LH
  2. Speed sensor rotor

HINT:
  1. DTCs C1413 and C1275 are for the front speed sensor RH.
  2. DTCs C1414 and C1276 are for the front speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1405 and C1406 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Check the speed sensor signal after cleaning or replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection/ Error or Normal
    Normal
    -
    FL Speed Open
    Front speed sensor LH open detection/ Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 9
OK


2. READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK


3. PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the signal check in the Test Mode Procedure (Click here).

    OK:
    All test mode DTCs are cleared.



NG
Go to step 5
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTCs C1413 and C1414 are not output
    A
    DTCs C1413 and/or C1414 are output
    B



B
Go to step 12
A

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK FRONT SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C144929E33
    Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the front steering knuckle.
    The installation bolt is tightened properly.
    Torque:
    8.5 N*m (87 kgf*cm, 75 in.*lbf)

    Text in Illustration 
    *1
    Front Speed Sensor
    *a
    No clearance
    *b
    OK
    *c
    NG



NG
INSTALL FRONT SPEED SENSOR CORRECTLY
OK


6. INSPECT FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7. INSPECT FRONT SPEED SENSOR ROTOR
  1. Remove the front axle with ABS rotor bearing assembly (Click here).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    HINT:
    The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
    If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR
OK


8. INSPECT SKID CONTROL SENSOR WIRE
  1. Remove the skid control sensor wire.

  1. C214500E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    AV1-1 - V1-1 (FR-)
    Always
    Below 1 Ω
    AV1-2 - V1-2 (FR+)
    Always
    Below 1 Ω
    AV1-1 - AV1-2
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    AW1-1 - W1-1 (FL-)
    Always
    Below 1 Ω
    AW1-2 - W1-2 (FL+)
    Always
    Below 1 Ω
    AW1-1 - AW1-2
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Skid Control Sensor Wire
    *a
    for RH
    *b
    for LH



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Install the skid control sensor wire.

  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the V1 and/or W1 front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A4-3 (FR+) - V1-2 (FR+)
    Always
    Below 1 Ω
    A4-3 (FR+) - Body ground
    Always
    10 kΩ or higher
    A4-17 (FR-) - V1-1 (FR-)
    Always
    Below 1 Ω
    A4-17 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A4-18 (FL+) - W1-2 (FL+)
    Always
    Below 1 Ω
    A4-18 (FL+) - Body ground
    Always
    10 kΩ or higher
    A4-4 (FL-) - W1-1 (FL-)
    Always
    Below 1 Ω
    A4-4 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK TERMINAL VOLTAGE (FR+, FL+)
  1. Disconnect the V1 and/or W1 front speed sensor connector.

  1. Connect the A4 skid control ECU connector.

  1. C207217E11
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    V1-2 (FR+) - Body ground
    Ignition switch ON
    11 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    W1-2 (FL+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)
    *b
    for RH
    *c
    for LH



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK


11. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTCs C1413 and C1414 are not output
    A
    DTCs C1413 and/or C1414 are output
    B



B
Go to step 12
A

USE SIMULATION METHOD TO CHECK (Click here)

12. REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor (Click here).


NEXT


13. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTCs C1413 and C1414 are not output
    A
    DTCs C1413 and/or C1414 are output
    B



B
REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY (Click here)
A

END


← C1413 Front Speed Sensor RH Output Malfunction (+ C1275, C1276, C1414) (Nov 2010 – Jul 2012)C1415 Rear Speed Sensor RH Output Malfunction (+ C1277, C1278, C1416) (Nov 2010 – Jul 2012) →