Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM
A-TRAC Indicator Light Remains ON
Circuit diagnosis · Vehicles built Aug 2012 – Oct 2012
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012
DESCRIPTION
This is the A-TRAC main switch circuit. When the A-TRAC switch is turned on with the transfer in L4(for automatic transmission) or LL(for manual transmission), the A-TRAC function is available and the A-TRAC indicator light illuminates. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here ).
1. CHECK CAN COMMUNICATION LINE
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here ).
OK:
CAN Bus Check indicates no malfunctions in CAN communication.
NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here )
OK
2. CHECK FOR DTC
Check for DTCs (Click here ).
Result
Result
Proceed to
DTC is not output
A
DTC is output
B
B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here )
A
3. READ VALUE USING INTELLIGENT TESTER (A-TRAC INDICATOR LIGHT)
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Check the condition of the A-TRAC switch by operating the intelligent tester.
ABS/VSC/TRC
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A-TRAC Indicator Light
A-TRAC indicator light/ ON or OFF
ON: Indicator light on OFF: Indicator light off
-
OK:
The intelligent tester displays ON or OFF according to A-TRAC switch operation.
NG
OK
4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Perform Active Test of the combination meter using the intelligent tester (Click here ).
Check that the A-TRAC indicator light turns on and off on the combination meter when using the intelligent tester.
OK:
The A-TRAC indicator light turns ON or OFF according to the intelligent tester operations.
NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here )
OK
5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - A-TRAC SWITCH)
w/ CRAWL
Disconnect the A4 skid control ECU connector.
Disconnect the Q1 A-TRAC switch connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-13 (ATRC) - Q1-8 (ATRC)
Always
Below 1 Ω
A4-13 (ATRC) - Body ground
Always
10 k Ω or higher
Q1-8 (ATRC) - Body ground
Always
10 k Ω or higher
Q1-5 (E) - Body ground
Always
Below 1 Ω
w/o CRAWL
Disconnect the A4 skid control ECU connector.
Disconnect the E15 A-TRAC switch connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-13 (ATRC) - E15-3
Always
Below 1 Ω
A4-13 (ATRC) - Body ground
Always
10 k Ω or higher
E15-3 - Body ground
Always
10 k Ω or higher
E15-4 - Body ground
Always
Below 1 Ω
Result
Result
Proceed to
OK (w/ CRAWL)
A
OK (w/o CRAWL)
B
NG
C
B
C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A
6. INSPECT TRANSFER POSITION SWITCH (A-TRAC SWITCH)
Remove the A-TRAC switch (Click here ).
Inspect the A-TRAC switch (Click here ).
NG
REPLACE TRANSFER POSITION SWITCH (A-TRAC SWITCH)
OK
7. INSPECT TRACTION CONTROL SWITCH NO. 2 (A-TRAC SWITCH)
Remove the A-TRAC switch (Click here ).
Inspect the A-TRAC switch (Click here ).
NG
REPLACE TRACTION CONTROL SWITCH NO. 2 (A-TRAC SWITCH)
OK