2011-2016 FJ Cruiser · Service Manual BRAKE

A-TRAC Indicator Light does not Come ON

Circuit diagnosis · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012

DESCRIPTION

The A-TRAC does not operate even if the A-TRAC switch is pressed under the following conditions:
  1. The TRC or VSC system is faulty.
  2. The temperature inside the hydraulic brake booster increases and the A-TRAC operation is suspended.

WIRING DIAGRAM

Refer to A-TRAC Indicator Light Remains ON (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2. INSPECT TRACTION CONTROL SWITCH NO.2 (A-TRAC SWITCH)
  1. Remove the A-TRAC switch.

  1. C234072E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (A-TRAC Switch)



NG
REPLACE TRACTION CONTROL SWITCH NO.2 (A-TRAC SWITCH)
OK


3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - A-TRAC SWITCH)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the E15 A-TRAC switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-13 (ATRC) - E15-3
    Always
    Below 1 Ω
    A4-13 (ATRC) - Body ground
    Always
    10 k Ω or higher
    E15-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. READ VALUE USING INTELLIGENT TESTER (A-TRAC INDICATOR LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. Check the condition of the A-TRAC switch by operating the tester.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A-TRAC Indicator Light
    A-TRAC indicator light/ ON or OFF
    ON: Indicator light on
    ON: Indicator light off
    -

    OK:
    The tester displays ON or OFF according to A-TRAC switch operation.



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)


← A-TRAC Indicator Light does not Come ON (Aug 2009 – Oct 2010)A-TRAC Indicator Light does not Come ON (Aug 2012 – Oct 2012) →