A-TRAC Indicator Light does not Come ON
Circuit diagnosis · Vehicles built from Nov 2012
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012
DESCRIPTION
The A-TRAC does not operate even if the A-TRAC switch is pressed under the following conditions:
- The TRC or VSC system is faulty.
- The temperature inside the hydraulic brake booster increases and the A-TRAC operation is suspended.
WIRING DIAGRAM
Refer to A-TRAC Indicator Light Remains ON (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK CAN COMMUNICATION LINE
|
 |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
|
NG |
 |
|
| GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
|
|
|
| OK |
|
 |
|
| 2. CHECK FOR DTC
|
 |
Check for DTCs (Click here).
Result
Result
|
Proceed to
|
DTC is not output
|
A
|
DTC is output
|
B
|
|
B |
 |
|
| REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
|
|
|
| A |
|
 |
|
| 3. READ VALUE USING INTELLIGENT TESTER (A-TRAC INDICATOR LIGHT)
|
 |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Check the condition of the A-TRAC switch by operating the intelligent tester.
ABS/VSC/TRC
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
A-TRAC Indicator Light
|
A-TRAC indicator light/ ON or OFF
|
ON: Indicator light on OFF: Indicator light off
|
-
|
- OK:
- The intelligent tester displays ON or OFF according to A-TRAC switch operation.
|
NG |
 |
|
| CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - A-TRAC SWITCH)
|
|
|
| OK |
|
 |
|
| 4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
|
 |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Perform Active Test of the combination meter using the intelligent tester (Click here).
Check that the A-TRAC indicator light turns on and off on the combination meter when using the intelligent tester.
- OK:
- The A-TRAC indicator light turns ON or OFF according to the intelligent tester operations.
|
NG |
 |
|
| GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
|
|
|
| OK |
|
 |
|
|
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - A-TRAC SWITCH)
|
 |
w/ CRAWL
Disconnect the A4 skid control ECU connector.
Disconnect the Q1 A-TRAC switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A4-13 (ATRC) - Q1-8 (ATRC)
|
Always
|
Below 1 Ω
|
A4-13 (ATRC) - Body ground
|
Always
|
10 k Ω or higher
|
Q1-8 (ATRC) - Body ground
|
Always
|
10 k Ω or higher
|
Q1-5 (E) - Body ground
|
Always
|
Below 1 Ω
|
w/o CRAWL
Disconnect the A4 skid control ECU connector.
Disconnect the E15 A-TRAC switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A4-13 (ATRC) - E15-3
|
Always
|
Below 1 Ω
|
A4-13 (ATRC) - Body ground
|
Always
|
10 k Ω or higher
|
E15-3 - Body ground
|
Always
|
10 k Ω or higher
|
E15-4 - Body ground
|
Always
|
Below 1 Ω
|
Result
Result
|
Proceed to
|
OK (w/ CRAWL)
|
A
|
OK (w/o CRAWL)
|
B
|
NG
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| A |
|
 |
|
| 6. INSPECT TRANSFER POSITION SWITCH (A-TRAC SWITCH)
|
 |
Remove the A-TRAC switch (Click here).
Inspect the A-TRAC switch (Click here).
|
NG |
 |
|
| REPLACE TRANSFER POSITION SWITCH (A-TRAC SWITCH) (Click here)
|
|
|
| OK |
|
 |
|
|
| 7. INSPECT TRACTION CONTROL SWITCH NO.2 (A-TRAC SWITCH)
|
 |
Remove the A-TRAC switch (Click here).
Inspect the A-TRAC switch (Click here).
|
NG |
 |
|
| REPLACE TRACTION CONTROL SWITCH NO.2 (A-TRAC SWITCH) (Click here)
|
|
|
| OK |
|
 |
|
|