Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and the long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim is considerably in error to lean side (2 trip detection logic)
  1. Intake system
  2. Injector blockage
  3. Mass Air Flow (MAF) meter
  4. Engine Coolant Temperature (ECT) sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  8. A/F sensor (bank 1, 2 sensor 1)
  9. A/F sensor heater (bank 1, 2 sensor 1)
  10. A/F HEATER relay
  11. A/F sensor heater and A/F HEATER relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. Wire harness or connector
  15. ECM
P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim is considerably in error to rich side (2 trip detection logic)
  1. Injector leak or blockage
  2. MAF meter
  3. ECT sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  8. A/F sensor (bank 1, 2 sensor 1)
  9. A/F sensor heater (bank 1, 2 sensor 1)
  10. A/F HEATER relay
  11. A/F sensor heater and A/F HEATER relay circuits
  12. Wire harness or connector
  13. ECM

HINT:
  1. When DTC P0171 or P0174 is stored, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be stored. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air- fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learning value is +35% or more, or -35% or less, the ECM interprets this as a fuel system malfunction.

A121607E01


MONITOR STRATEGY


Related DTCs
P0171: Fuel trim Lean (bank 1)
P0172: Fuel trim Rich (bank 1)
P0174: Fuel trim Lean (bank 2)
P0175: Fuel trim Rich (bank 2)
Required Sensors/Components (Main)
Fuel system
Required Sensors/Components (Related)
Air fuel ratio sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Fuel-trim 
Monitor runs whenever following DTCs not present
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - advance)
P0012, P0022 (VVT system - retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - advance)
P0015, P0025 (Exhaust VVT system - retard)
P0016, P0018 (VVT system - misalignment)
P0017, P0019 (Exhaust VVT system - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0412, P0418, P1613 (Secondary air injection system control)
P0416, P0417, P2440 - P2445 (Secondary air injection system)
P0500 (Vehicle speed sensor)
P219A, P219B (Air-fuel ratio imbalance)
Fuel system status
Closed-loop
Battery voltage
11 V or more
Either of following conditions 1 or 2 met
-
1. Engine speed
Less than 1100 rpm
2. Engine load
10% or more
Catalyst monitor
Not executed

TYPICAL MALFUNCTION THRESHOLDS


Fuel-trim 
EVAP Purge-cut
Executing
Either of following conditions 1 or 2 met
-
1. Average between short-term fuel trim and long-term fuel trim
35% or more (varies with ECT)
2. Average between short-term fuel trim and long-term fuel trim
-35% or less (varies with ECT)

CONFIRMATION DRIVING PATTERN


A199233E32

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or more) with all the accessories switched OFF [B].
  7. With the engine warmed up, idle the engine for 2 minutes or more [C].
  8. Drive the vehicle at between 60 km/h and 120 km/h (37 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    If a pending DTC is output, the system is malfunctioning.

  11. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 for the air fuel ratio sensor circuit .
Refer to DTC P0102 for the mass air flow meter circuit .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  6. Sensor 1 refers to the sensor closest to the engine assembly.
  7. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0171, P0172, P0174 or P0175 is output
    A
    P0171, P0172, P0174 or P0175 and other DTCs are output
    B

HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak from intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the 12.5 or -12.5 button to change the fuel injection volume).

  1. Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The A/F sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard Voltage:

    Techstream Display (Sensor)
    Injection Volumes
    Status
    Voltages
    AFS Voltage B1S1 or AFS Voltage B2S1 (A/F)
    12.5%
    Rich
    Less than 3.1 V
    -12.5%
    Lean
    More than 3.4 V
    O2S B1S2 or O2S B2S2 (HO2)
    12.5%
    Rich
    More than 0.55 V
    -12.5%
    Lean
    Less than 0.4 V


    Result 
    Status AFS Voltage B1S1 or AFS Voltage B2S1
    Status O2S B1S2 or O2S B2S2
    A/F Condition and A/F Sensor Condition
    Suspected Trouble Areas
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    A
    Lean
    Lean
    Actual air-fuel ratio lean
    1. PCV valve and hose
    2. PCV hose connections
    3. Injector blockage
    4. Gas leak from exhaust system
    5. Intake system
    6. Fuel pressure
    7. Mass Air Flow (MAF) meter
    8. Engine Coolant Temperature (ECT) sensor
    Rich
    Rich
    Actual air-fuel ratio rich
    1. Injector leakage or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. MAF meter
    6. ECT sensor
    Lean
    Lean/Rich
    A/F sensor malfunction
    A/F sensor
    B
    Rich
    Lean: During Control the Injection Volume for A/F Sensor, the A/F sensor output voltage (AFS) is consistently more than 3.4 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.
    Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.
    Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternates correctly.



B
Go to step 11
A


5.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 100°C (167°F and 212°F).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec and 25.8 gm/sec (shift lever: N (Neutral); A/C: Off).



NG
Go to step 16
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FOR SPARKS AND IGNITION

HINT:
  1. Refer to the ignition system inspection procedure (Click here).
  2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).
  3. Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here).



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

HINT:
  1. Refer to the fuel injector assembly inspection procedure (Click here).
  2. If the injectors malfunction, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).
  3. Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the A/F sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
A079114E57
  1. Disconnect the B33 and B31 A/F sensor connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B33-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B31-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to A/F Sensor)
    *b
    Bank 1
    *c
    Bank 2



NG
Go to step 21
OK


13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
  1. Disconnect the B33 and B31 A/F sensor connectors.

  1. Disconnect the B50 and B49 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) - B50-17 (HA1A)
    Always
    Below 1 Ω
    B33-3 (A1A+) - B49-1 (A1A+)
    Always
    Below 1 Ω
    B33-4 (A1A-) - B49-2 (A1A-)
    Always
    Below 1 Ω
    B31-1 (HA2A) - B50-19 (HA2A)
    Always
    Below 1 Ω
    B31-3 (A2A+) - B49-7 (A2A+)
    Always
    Below 1 Ω
    B31-4 (A2A-) - B49-8 (A2A-)
    Always
    Below 1 Ω
    B33-1 (HA1A) or B50-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B33-3 (A1A+) or B49-1 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B33-4 (A1A-) or B49-2 (A1A-) - Body ground
    Always
    10 kΩ or higher
    B31-1 (HA2A) or B50-19 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B31-3 (A2A+) or B49-7 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B31-4 (A2A-) or B49-8 (A2A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the A/F sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC P0171, P0172, P0174 or P0175 is output
    B



B
Go to step 16
A

END 

16.CHECK HARNESS OR CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    P0171, P0172, P0174 or P0175 is output
    A
    No output
    B



B
END
A


18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the B51 Mass Air Flow (MAF) meter connector.

  1. Disconnect the B48 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) - B48-14 (VG)
    Always
    Below 1 Ω
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω
    B51-5 (VG) or B48-14 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19.REPLACE MASS AIR FLOW METER
  1. Replace the MAF meter (Click here).

    HINT:
    1. If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the MAF meter.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).


NEXT


20.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No output
    A
    P0171, P0172, P0174 or P0175 is output
    B



B
REPLACE ECM (Click here)
A

END 

21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F HEATER RELAY)
  1. Disconnect the B33 and B31 A/F sensor connectors.

  1. Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    B33-2 (+B) - 3 (A/F HEATER relay)
    Always
    Below 1 Ω
    B31-2 (+B) - 3 (A/F HEATER relay)
    Always
    Below 1 Ω
    B33-2 (+B) or 3 (A/F HEATER relay) - Body ground
    Always
    10 kΩ or higher
    B31-2 (+B) or 3 (A/F HEATER relay) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22.INSPECT A/F HEATER RELAY
  1. Inspect the A/F HEATER relay (Click here).



NG
REPLACE A/F HEATER RELAY
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)