2014-2019 Hiace · Service Manual BRAKE

C1415 Rear Speed Sensor RH Output Malfunction

Diagnostic trouble codes · Vehicles built from Dec 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

DESCRIPTION Refer to DTCs C1403 and C1404 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
C1415
C1416
Either of the following is detected:
  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Rear speed sensor RH/LH
  2. Rear skid control rotor RH/LH
  3. Sensor installation
  4. Skid control ECU (Brake actuator assembly)
  5. Wire harness or connector

HINT:
  1. DTC C1415 is for the rear speed sensor RH.
  2. DTC C1416 is for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1403 and C1404 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    Rear speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RL Speed Open
    Rear speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption

    OK:
    Normal (There are no momentary interruptions.)

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2. READ VALUE USING GTS (REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTCs C1415 and C1416 are not output
    A
    DTCs C1415 and/or C1416 are output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK REAR SPEED SENSOR INSTALLATION


NG
INSTALL REAR SPEED SENSOR CORRECTLY (Click here)
OK


5. INSPECT REAR SPEED SENSOR TIP


NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


6. INSPECT REAR SPEED SENSOR ROTOR
  1. Remove the rear axle shaft with backing plate (Click here).

  1. Check the front skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

  1. Reinstall the rear speed sensor and the rear axle shaft with backing plate (Click here for speed sensor, Click here for rear axle shaft with backing plate)

    Result:
    Result
    Proceed to
    OK (for LH)
    A
    OK (for RH)
    B
    NG
    C



B
Go to step 8

C
CLEAN OR REPLACE REAR SKID CONTROL ROTOR
A


7. INSPECT REAR SPEED SENSOR RH


NG
REPLACE REAR SPEED SENSOR RH (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)


NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

REPLACE REAR SPEED SENSOR (Click here)


← C1415 Rear Speed Sensor RH Output Malfunction (+ C1416) (Jan 2017 – Nov 2017)C1417 High Power Supply Voltage Malfunction (Jan 2015 – Mar 2016) →