2014-2019 Hiace · Service Manual BRAKE

Brake Warning Light Remains ON

Circuit diagnosis · Vehicles built from Dec 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
  2. The brake fluid level is insufficient.
  3. EBD operation is not possible.
  4. The vacuum inside the brake booster decreases.
  5. The parking brake is applied

WIRING DIAGRAM

C321039E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK CAN COMMUNICATION LINE


B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED


NG
CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY
OK


3. INSPECT BATTERY


NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY
OK


4. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6. CHECK ENGINE TYPE
  1. Check the engine type.

    Result:
    Result
    Proceed to
    1KD-FTV or 2KD-FTV
    A
    1TR-FE or 2TR-FE
    B



B
Go to step 9
A


7. INSPECT VACUUM WARNING SWITCH ASSEMBLY
  1. Turn the ignition switch off.

  1. Disconnect the A43 vacuum warning switch assembly connector.

  1. Inspect the vacuum warning switch assembly (Click here).

    OK:
    The vacuum warning switch assembly is normal.



NG
REPLACE VACUUM WARNING SWITCH ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
  1. Disconnect the H20 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H20-32 (BRL) or A43-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
C235854E06
  1. Turn the ignition switch off.

  1. Remove the reservoir filler cap and strainer.

  1. Disconnect the A10 brake fluid level warning switch (brake master cylinder sub-assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (E)
    Switch off (Float up)
    Below 1 Ω
    Switch on (Float down)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-assembly))

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H20-31 (B/LE) or A10-1 (+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT PARKING BRAKE SWITCH ASSEMBLY
  1. Disconnect the B3 parking brake switch assembly connector.

  1. Inspect the parking brake switch assembly (Click here).

    OK:
    The parking brake switch assembly is normal.



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
OK


12. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H20-11 (PKBI) or B3-1 or B92-3 (PKB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. READ VALUE USING GTS (BRAKE WARNING LIGHT)
  1. Reinstall the reservoir filler cap and strainer.

  1. Reconnect the H20 combination meter assembly connector, A43 vacuum warning switch assembly connector*, A10 brake fluid level warning switch (brake master cylinder sub-assembly) connector, B3 parking brake switch assembly connector and B92 skid control ECU (brake actuator assembly) connector.

    1. *: for 1KD and 2KD-FTV

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Brake Warning Light
    Brake warning light/ ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -

  1. Check the GTS display condition of the brake warning light.

    Result:
    Result
    Proceed to
    Display of the Data List remains OFF
    A
    Display of the Data List remains ON
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT METER / GAUGE SYSTEM (Click here)


← Brake Warning Light Remains ON (Jan 2017 – Nov 2017)Brake Warning Light does not Come ON (Jan 2015 – Mar 2016) →