Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM
Brake Warning Light Remains ON
Circuit diagnosis · Vehicles built Jan 2017 – Nov 2017
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication. If any of the following is detected, the brake warning light remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
The brake fluid level is insufficient.
EBD operation is not possible.
The vacuum inside the brake booster decreases.
The parking brake is applied
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here ).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1. CHECK CAN COMMUNICATION LINE
Check if CAN communication system DTCs are output (Click here ).
Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
B
A
2. CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
OK:
The connector is securely connected.
NG
CONNECT CONNECTOR TO BRAKE
ACTUATOR ASSEMBLY CORRECTLY
OK
3. INSPECT BATTERY
Check the battery voltage.
Standard voltage:
11 to 14 V
HINT:
NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY
OK
4. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
Turn the ignition switch off.
Disconnect the B92 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
B92-12 (IG1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration
*a
Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly))
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK
5. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
B92-25 (GND1) - Body ground
Always
Below 1 Ω
Text in Illustration
*a
Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly))
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK
6. CHECK ENGINE TYPE
Check the engine type.
Result:
Result
Proceed to
1KD-FTV or 2KD-FTV
A
1TR-FE or 2TR-FE
B
B
A
7. INSPECT VACUUM WARNING SWITCH ASSEMBLY
Turn the ignition switch off.
Disconnect the A43 vacuum warning switch assembly connector.
Inspect the vacuum warning switch assembly (Click here ).
OK:
The vacuum warning switch assembly is normal.
NG
REPLACE VACUUM WARNING SWITCH ASSEMBLY (Click here )
OK
8. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
Disconnect the H20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
H20-32 (BRL) or A43-2 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
9. INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the A10 brake fluid level warning switch (brake master cylinder sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
HINT:
A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 (+) - 2 (E)
Switch off (Float up)
Below 1 Ω
Switch on (Float down)
10 kΩ or higher
Text in Illustration
*a
Component without harness connected (Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-assembly))
HINT:
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (Click here )
OK
10. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
H20-31 (B/LE) or A10-1 (+) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
11. INSPECT PARKING BRAKE SWITCH ASSEMBLY
Disconnect the B3 parking brake switch assembly connector.
Inspect the parking brake switch assembly (Click here ).
OK:
The parking brake switch assembly is normal.
NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here )
OK
12. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY)
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
H20-11 (PKBI) or B3-1 or B92-3 (PKB) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
13. READ VALUE USING GTS (BRAKE WARNING LIGHT)
Reinstall the reservoir filler cap and strainer.
Reconnect the H20 combination meter assembly connector, A43 vacuum warning switch assembly connector*, A10 brake fluid level warning switch (brake master cylinder sub-assembly) connector, B3 parking brake switch assembly connector and B92 skid control ECU (brake actuator assembly) connector.
*: for 1KD and 2KD-FTV
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
ABS/VSC/TRC
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Brake Warning Light
Brake warning light/ ON or OFF
ON: Warning light on OFF: Warning light off
-
Check the GTS display condition of the brake warning light.
Result:
Result
Proceed to
Display of the Data List remains OFF
A
Display of the Data List remains ON
B
B
A