2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. REMOVE ENGINE ASSEMBLY
(Click here)

2. INSTALL ENGINE STAND

3. REMOVE VANE PUMP ASSEMBLY

  1. C101372E01
    Remove the 2 nuts and the vane pump assembly.

  1. Remove the vane pump O-ring from the vane pump assembly.


4. REMOVE TIMING GEAR COVER INSULATOR

  1. A148171
    Remove the bolt and timing gear cover insulator.


5. REMOVE VACUUM PUMP ASSEMBLY

  1. A102102
    Remove the 2 nuts, vacuum pump and 2 O-rings.


6. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the wire harness clamp.

  1. A156650
    Remove the 6 bolts, 6 washers and timing belt cover.


7. REMOVE TIMING BELT
(Click here)

8. REMOVE CRANKSHAFT POSITION SENSOR

A102284
  1. Disconnect the crankshaft position sensor connector.

  1. Separate the connector from the No. 1 vacuum pipe .

  1. A151576
    Separate the 3 wire harness clamps.

  1. Remove the bolt and the crankshaft position sensor.


9. REMOVE CAMSHAFT POSITION SENSOR

A102283
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.


10. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. w/o DPF:

    1. A177101
      Disconnect the diesel turbo pressure sensor connector and vacuum switching valve connector.

    2. Remove the bolt and disconnect the wire harness clamp.

  1. Disconnect the 2 diesel throttle body connectors.

  1. A257142E01
    Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.


11. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

12. REMOVE EGR COOLER ASSEMBLY
(Click here)

13. REMOVE COMMON RAIL ASSEMBLY
(Click here)

14. REMOVE FUEL SUPPLY PUMP ASSEMBLY
(Click here)

15. REMOVE INJECTOR ASSEMBLY
(Click here)

16. REMOVE CAMSHAFT TIMING PULLEY

  1. A100848
    Remove the bolt and camshaft timing pulley while holding the camshaft with a wrench.

  1. A323634E01
    Using SST, remove the camshaft timing pulley and set key.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-05010, 09957-04010)
    09955-04150  

  1. A070551E02
    Rotate the crankshaft approximately 90° counterclockwise from TDC to lower the piston.


17. REMOVE NO. 2 TIMING BELT COVER

  1. A051300E01
    Remove the nut, 4 bolts and No. 2 timing belt cover.


18. REMOVE WATER PUMP ASSEMBLY

  1. A051307
    Remove the 5 bolts, 2 nuts and water pump assembly.


19. REMOVE CRANKSHAFT PULLEY

  1. A142434E01
    Using SST, remove the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A142416E01
    Using SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.


20. REMOVE ENGINE OIL LEVEL SENSOR

A145768
  1. Disconnect the engine oil level sensor connector.

  1. Remove the 4 bolts and engine oil level sensor.


21. REMOVE OIL PAN SUB-ASSEMBLY

  1. A239346
    Disconnect the vinyl tube from the oil pan.

  1. A074128E02
    Remove the 22 bolts and 2 nuts.

  1. A057637E04
    Insert the blade of an oil pan seal cutter between the oil pan and cylinder block stiffening plate, cut through the applied sealer, and then remove the oil pan and cylinder block stiffening plate.

    NOTICE:
    1. Do not use an oil pan seal cutter for the timing gear case side and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.


22. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A102736
    Remove the 2 bolts, 2 nuts, oil strainer and gasket.


23. REMOVE TIMING GEAR COVER

NOTICE:
As the fuel supply pump is not installed, the injection gear is loose inside the timing gear case. Do not allow the injection gear to fall.

HINT:
To prevent the injection gear from falling, temporarily install the fuel supply pump.

  1. A100853
    Remove the 14 bolts and 2 nuts.

  1. A102800
    Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.

    NOTICE:
    Do not damage the contact surface.

  1. A060162E03
    Remove the O-ring from the timing gear case.

  1. A102771
    Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.


24. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

  1. A100854
    Using a screwdriver and hammer, tap out the oil seal.


25. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

  1. A100856
    Using a screwdriver and hammer, tap out the oil seal.


26. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A060163E01
    Remove the No. 1 crankshaft position sensor plate.


27. REMOVE INJECTION GEAR

  1. A102772
    Remove the injection gear.


28. REMOVE CRANKSHAFT TIMING GEAR

  1. A100863E02
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)


29. REMOVE IDLE GEAR THRUST PLATE

  1. A102775
    Remove the 2 bolts and idle gear thrust plate.


30. REMOVE NO. 1 IDLE GEAR

  1. A100860
    Remove the No. 1 idle gear together with the No. 2 idle sub gear.

    NOTICE:
    Make sure that the No. 2 idle sub gear and No. 1 idle gear are correctly fitted to each other.


31. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A100885
    Remove the No. 1 idle gear shaft.


32. REMOVE TIMING GEAR CASE ASSEMBLY

  1. A100878
    Remove the union bolt and 8 bolts.

  1. A102853E02
    Pry the timing gear case at the location shown in the illustration and remove the timing gear case.

    NOTICE:
    Do not drop the driven rotor.

  1. A100876E02
    Remove the gasket from the timing gear case.

  1. A059946E01
    Remove the driven rotor from the timing gear case.

  1. A069840E03
    Remove the 2 O-rings from the cylinder block.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →