2014-2019 Hiace · Service Manual ENGINE

PROBLEM SYMPTOMS TABLE

Troubleshooting · Vehicles built from Jan 2015

HINT:
  1. Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  2. Inspect the fuses and relays related to this system before inspecting the suspected areas below.

SFI System 
Symptom
Suspected Area
See page
Engine does not crank (Does not start)
Battery
Click here
Starter
Click here
Starter relay
Click here
Park/neutral position switch assembly (for A/T)
Click here
VC output circuit
Click here
No initial combustion (Does not start)
ECM power source circuit
Click here
Crankshaft position sensor
Click here
Camshaft position sensor
Click here
Ignition system
Click here
Fuel pump control circuit
Click here
Fuel injector circuit
Click here
ECM
Click here
VC output circuit
Click here
Starter signal circuit
Click here
Engine immobiliser system
Click here
No. 1 valve rocker arm sub-assembly*
-
Engine cranks normally but has difficulty in starting
Fuel pump control circuit
Click here
Engine coolant temperature sensor
Click here
Ignition system
Click here
Compression
Click here
Fuel injector
Click here
Fuel injector circuit
Click here
Air induction system
-
Electronic throttle control system
Click here
PCV hose
Click here
Starter signal circuit
Click here
ECM power source circuit
Click here
No. 1 valve rocker arm sub-assembly*
-
Difficult to start with cold engine
Ignition system
Click here
Spark plug
Click here
Fuel pump control circuit
Click here
Fuel injector
Click here
Starter signal circuit
Click here
Difficult to start with warm engine
Fuel injector
Click here
Ignition system
Click here
Spark plug
Click here
Fuel pump control circuit
Click here
Starter signal circuit
Click here
High engine idle speed
Electronic throttle control system
Click here
A/C signal circuit
Click here
ECM power source circuit
Click here
Low engine idle speed (Poor idling)
Electronic throttle control system
Click here
A/C signal circuit
Click here
Fuel pump control circuit
Click here
Air induction system
-
PCV hose
Click here
Rough idling
Compression
Click here
Spark plug
Click here
Fuel injector
Click here
Ignition system
Click here
Fuel pump control circuit
Click here
Electronic throttle control system
Click here
Air induction system
-
PCV hose
Click here
Mass air flow meter
Click here
No. 1 valve rocker arm sub-assembly*
-
Hunting (Poor idling)
Electronic throttle control system
Click here
Air induction system
-
ECM power source circuit
Click here
Hesitation and/or poor acceleration
Fuel pump control circuit
Click here
Spark plug
Click here
Ignition system
Click here
Fuel injector
Click here
Mass air flow meter
Click here
Electronic throttle control system
Click here
Air induction system
-
Compression
Click here
Brake override system
Click here
No. 1 valve rocker arm sub-assembly*
-
Surging (Poor driveability)
Spark plug
Click here
Fuel pump control circuit
Click here
Ignition system
Click here
Fuel injector
Click here
Mass air flow meter
Click here
Variable valve timing system
Click here
Compression
Click here
No. 1 valve rocker arm sub-assembly*
-
Engine stalls soon after starting
Fuel pump control circuit
Click here
Spark plug
Click here
Ignition system
Click here
Fuel injector
Click here
Variable valve timing system
Click here
Electronic throttle control system
Click here
Air induction system
-
PCV hose
Click here
Compression
Click here
No. 1 valve rocker arm sub-assembly*
-
Engine stalls only during A/C operation
A/C signal circuit
Click here
ECM
Click here

HINT:
*: Check the "Fuel Cut Elps Time" in the Data List.
If the elapsed time is over 0 sec, then the engine speed is high (More than the engine speed at which fuel cut occurs + 500 rpm).
When this has happened, there is the possibility that the valve rocker arm will become loose and malfunction, so check that the No. 1 valve rocker arm sub-assembly is properly attached (Click here).

← INITIALIZATION (from Jan 2015)TERMINALS OF ECM (from Jan 2015) →