2014-2019 Hiace · Service Manual BRAKE

C1413 Front Speed Sensor RH Output Malfunction

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
C1413
C1414
Either of the following is detected:
  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Front speed sensor RH/LH
  2. Front skid control rotor RH/LH
  3. Sensor installation
  4. Wire harness or connector
  5. Skid control ECU (Brake actuator assembly)

HINT:
  1. DTC C1413 is for the front speed sensor RH.
  2. DTC C1414 is for the front speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1401 and C1402 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FL Speed Open
    Front speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption

    OK:
    Normal (There are no momentary interruptions.)

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2. READ VALUE USING GTS (FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTCs C1413 and C1414 are not output
    A
    DTCs C1413 and/or C1414 are output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK FRONT SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C168336E13
    Check the speed sensor installation (Click here).

    OK:
    There is no clearance between the sensor and the front steering knuckle.
    The installation bolt is tightened properly.

    Text in Illustration 
    *a
    Normal
    *b
    Abnormal
    *c
    Clearance



NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Click here)
OK


5. INSPECT FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    1. If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
    3. Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


6. INSPECT FRONT SPEED SENSOR ROTOR
  1. Remove the front skid control rotor (Click here).

  1. Check the front skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

  1. Reinstall the front speed sensor and the front skid control rotor (Click here for speed sensor, Click here for skid control rotor).



NG
CLEAN OR REPLACE FRONT SKID CONTROL ROTOR
OK


7. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Disconnect the B18 or B20 front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    B92-31 (FR+) - B18-2
    Always
    Below 1 Ω
    B92-31 (FR+) or B18-2 - Body ground
    Always
    10 kΩ or higher
    B92-30 (FR-) - B18-1
    Always
    Below 1 Ω
    B92-30 (FR-) or B18-1 - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    B92-18 (FL+) - B20-2
    Always
    Below 1 Ω
    B92-18 (FL+) or B20-2 - Body ground
    Always
    10 kΩ or higher
    B92-17 (FL-) - B20-1
    Always
    Below 1 Ω
    B92-17 (FL-) or B20-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)

  1. C321141E01
    Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    B18-2 - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Condition
    Specified Condition
    B20-2 - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

REPLACE FRONT SPEED SENSOR (Click here)


← C1413 Front Speed Sensor RH Output Malfunction (+ C1414) (Apr 2016 – Dec 2016)C1413 Front Speed Sensor RH Output Malfunction (+ C1414) (from Dec 2017) →