2014-2019 Hiace · Service Manual BODY ELECTRICAL

Speedometer Malfunction

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

WIRING DIAGRAM

E289624E04
E293043E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
  1. Use the Active Test to check the operation of the speedometer (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    OFF, 0, 40 or 80 (mph)*1
    Acceptable range (mph): [Control range → Speedometer display]
    1. 40 → 42.0 to 44.5
    2. 80 → 83.1 to 87.1
    OFF, 0, 40, 80, 120 or 160 (km/h)*2
    Acceptable range (km/h): [Control range → Speedometer display]*3
    1. 40 → 41.7 to 46.2
    2. 80 → 83.4 to 88.4
    3. 120 → 125.1 to 130.6
    4. 160 → 166.2 to 173.2
    Acceptable range (km/h): [Control range → Speedometer display]*4
    1. 40 → 41.0 to 45.5
    2. 80 → 82.0 to 87.0
    3. 120 → 122.8 to 128.3
    4. 160 → 163.8 to 170.3
    Acceptable range (km/h): [Control range → Speedometer display]*5
    1. 40 → 41.3 to 45.8
    2. 80 → 82.6 to 87.6
    3. 120 → 123.9 to 128.9
    4. 160 → 165.2 to 170.2
    Acceptable range (km/h): [Control range → Speedometer display]*6
    1. 40 → 40.2 to 44.5
    2. 80 → 80.5 to 85.5
    3. 120 → 120.7 to 126.2
    4. 160 → 160.9 to 167.4
    1. *1: for mph
    2. *2: for km/h
    3. *3: except Australia
    4. *4: except 1KD-FTV, Manual Transmission (for Australia)
    5. *5: for 1KD-FTV, Manual Transmission (for Australia)
    6. *6: for Automatic Transmission (for Australia)

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2. READ VALUE USING GTS (VEHICLE SPEED METER)
  1. Use the Data List to check if the speedometer is operating properly (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual vehicle speed
    -

    OK:
    Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Speedometer Sensor)
    B
    NG (w/ Speedometer Sensor)
    C



B
Go to step 3

C
Go to step 7
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

3. READ VALUE USING GTS (VEHICLE SPEED)
  1. Use the Data List to check if the speedometer is operating properly (Click here).

    ABS/VSC/TRC (w/ ABS) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Almost same as actual vehicle speed measured using speedometer tester
    -

    OK:
    Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o VSC)
    B
    NG (w/ VSC)
    C



B
GO TO ANTI-LOCK BRAKE SYSTEM (Click here)

C
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
A


4. CHECK COMBINATION METER ASSEMBLY (OUTPUT SIGNAL)

  1. C317023E03
    Disconnect the brake actuator assembly (skid control ECU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    w/o VSC 
    Tester Connection
    Condition
    Specified Condition
    B19-26 (SP1) - Body ground
    Ignition switch ON
    11 to 14 V
    w/ VSC 
    Tester Connection
    Condition
    Specified Condition
    B92-14 (SP1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    w/ VSC
    *B
    w/o VSC
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])



NG
Go to step 5
OK


5. CHECK COMBINATION METER ASSEMBLY (INPUT SIGNAL)

  1. E293672E01
    Check the input signal waveform using an oscilloscope.
    Item
    Condition
    Tester Connection
    H20-7 (SI) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Vehicle Condition
    Ignition switch ON, driving at approximately 20 km/h (12 mph)

    OK:
    The correct waveform appears as shown in the illustration.

    HINT:
    As vehicle speed increases, the cycle of the signal waveform narrows.

    Text in Illustration 
    *a
    Component with harness connected
    (Combination Meter Assembly)
    Result 
    Result
    Proceed to
    OK (w/o VSC)
    A
    OK (w/ VSC)
    B
    NG (w/o VSC)
    C
    NG (w/ VSC)
    D



B
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

C
GO TO ANTI-LOCK BRAKE SYSTEM (Click here)

D
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

6. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
  1. Disconnect the H20 combination meter assembly connector.

  1. Disconnect the B19*1 or B92*2 brake actuator assembly (skid control ECU) connector.

    1. *1: w/o VSC
    2. *2: w/ VSC

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o VSC 
    Tester Connection
    Condition
    Specified Condition
    H20-7 (SI) - B19-26 (SP1)
    Always
    Below 1 Ω
    H20-7 (SI) or B19-26 (SP1) - Body ground
    Always
    10 kΩ or higher
    w/ VSC 
    Tester Connection
    Condition
    Specified Condition
    H20-7 (SI) - B92-14 (SP1)
    Always
    Below 1 Ω
    H20-7 (SI) or B92-14 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

7. CHECK COMBINATION METER ASSEMBLY

  1. E293672E01
    Check the input signal waveform using an oscilloscope.
    Item
    Condition
    Tester Connection
    H20-7 (SI) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Vehicle Condition
    Ignition switch ON, driving at approximately 20 km/h (12 mph)

    OK:
    The correct waveform appears as shown in the illustration.

    HINT:
    As vehicle speed increases, the cycle of the signal waveform narrows.

    Text in Illustration 
    *a
    Component with harness connected
    (Combination Meter Assembly)



NG
Go to step 8
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

8. CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BATTERY)
  1. Disconnect the D38 speedometer sensor connector.

  1. Disconnect the H20 combination meter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D38-1 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D38-3 (SI) - H20-7 (SI)
    Always
    Below 1 Ω
    D38-2 (SE) - H20-35 (E3)
    Always
    Below 1 Ω
    D38-3 (SI) or H20-7 (SI) - Body ground
    Always
    10 kΩ or higher
    D38-2 (SE) or H20-35 (E3) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for 1KD-FTV)
    A
    OK (for 2KD-FTV)
    B
    NG
    C



B
REPLACE SPEEDOMETER SENSOR (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE SPEEDOMETER SENSOR (Click here)


← Speedometer Malfunction (Jan 2015 – Dec 2016)Tachometer Malfunction (Oct 2014 – Dec 2014) →