2014-2019 Hiace · Service Manual BODY ELECTRICAL

Tachometer Malfunction

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

The combination meter assembly receivers engine speed signals from the ECM via the CAN communication line. The combination meter assembly displays engine speed data that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E255800E01

INSPECTION PROCEDURE

NOTICE:
  1. Before starting following inspection, check if the SFI system*1 or ECD*2 system troubleshooting.
    1. *1: for 1TR-FE, 2TR-FE
    2. *2: for 1KD-FTV, 2KD-FTV, 5L-E
    1. for 1TR-FE: Click here
    2. for 2TR-FE (w/ Secondary Air Injection System): Click here
    3. for 2TR-FE (w/o Secondary Air Injection System): Click here
    4. for 1KD-FTV (w/ DPF): Click here
    5. for 1KD-FTV (w/o DPF): Click here
    6. for 2KD-FTV: Click here
    7. for 5L-E: Click here
  2. The meter/gauge system uses the CAN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the meter/gauge system after confirming that the communication systems are functioning properly.


1. CHECK FOR DTC (SFI SYSTEM*1 OR ECD SYSTEM*2)
  1. *1: for 1TR-FE, 2TR-FE
  2. *2: for 1KD-FTV, 2KD-FTV, 5L-E
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    SFI system *1 or ECD*2 system DTCs are not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1TR-FE)
    B
    NG (for 2TR-FE)
    NG (for 1KD-FTV)
    C
    NG (for 2KD-FTV)
    NG (for 5L-E)

    HINT:
    *: Go to procedure;
    1. for 1TR-FE: Click here
    2. for 2TR-FE (w/ Secondary Air Injection System): Click here
    3. for 2TR-FE (w/o Secondary Air Injection System): Click here
    4. for 1KD-FTV (w/ DPF): Click here
    5. for 1KD-FTV (w/o DPF): Click here
    6. for 2KD-FTV: Click here
    7. for 5L-E: Click here



B
GO TO SFI SYSTEM*

C
GO TO ECD SYSTEM*
A


2. PERFORM ACTIVE TEST USING GTS (TACHOMETER)
  1. Use the Active Test to check the operation of the tachometer (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tacho Meter Operation
    Tachometer
    OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000 (rpm)
    -

    HINT:
    Make sure that the vehicle is stopped and the engine is idling.

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3. READ VALUE USING GTS (ENGINE SPEED)
  1. Use the Data List to check if the tachometer is operating properly (Click here).

Combination Meter 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Engine Rpm
Engine speed / Min.: 0 rpm, Max.: 12750 rpm
Actual engine speed
-

OK:
Engine speed displayed on the GTS is almost the same as the actual engine speed.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4. READ VALUE USING GTS
  1. Use the Data List to check if the tachometer is operating properly (Click here).

Combination Meter 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Engine Rpm
Engine speed / Min.: 0 rpm, Max.: 12750 rpm
Actual engine speed
-
Engine and ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Engine Speed
Engine speed / Min.: 0 rpm, Max.: 16383 rpm
650 to 750 rpm: When idling
-

OK:
The data list values of the ECUs match.

HINT:
  1. When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
  2. When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
*: Replacement procedure;
  1. for 1TR-FE: Click here
  2. for 2TR-FE: Click here
  3. for 1KD-FTV: Click here
  4. for 2KD-FTV: Click here
  5. for 5L-E: Click here



NG
REPLACE ECM*
OK


5. CHECK COMBINATION METER ASSEMBLY
  1. Temporarily replace the combination meter assembly with a new one or normally functioning one (Click here).

  1. Check that the operation of the tachometer returns to normal (Click here).

    HINT:
    *: Replacement procedure;
    1. for 1TR-FE: Click here
    2. for 2TR-FE: Click here
    3. for 1KD-FTV: Click here
    4. for 2KD-FTV: Click here
    5. for 5L-E: Click here



NG
REPLACE ECM*
OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)


← Speedometer Malfunction (from Jan 2017)Tachometer Malfunction (Jan 2015 – Dec 2016) →