2014-2019 Hiace · Service Manual BODY ELECTRICAL

Fuel Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

WIRING DIAGRAM

E289622E02

INSPECTION PROCEDURE

NOTICE:
Be careful of flames.


1. PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
  1. Use the Active Test to check the operation of the fuel receiver gauge (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F
    -

    OK:
    Fuel receiver gauge is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2. READ VALUE USING GTS (FUEL INPUT)
  1. Use the Data List to check if the fuel receiver gauge is operating properly (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input signal/Min.: 0, Max. 127.5
    Current fuel level displayed
    Unit: Liters

    OK:
    Fuel amount value displayed on the GTS is almost the same as needle indication.

    Result 
    Result
    Proceed to
    NG
    A
    OK (Engine Type Diesel)
    B
    OK (Engine Type Gasoline)
    C



B
Go to step 3

C
Go to step 6
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY)
  1. Disconnect the H20 combination meter assembly connector.

  1. Disconnect the h1 front fuel main and return tube sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H20-33 (FUEL) - h1-2
    Always
    Below 1 Ω
    H20-34 (E2) - h1-3
    H20-33 (FUEL) or h1-2 - Body ground
    Always
    10 kΩ or higher
    H20-34 (E2) or h1-3 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

  1. E158805E11
    Remove the front fuel main and return tube sub-assembly.
    1. for 1KD-FTV: Click here
    2. for 2KD-FTV: Click here
    3. for 5L-E: Click here
    4. for 1GD-FTV: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-2
    Always
    Below 1 Ω
    A-3 - B-1

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1KD-FTV)
    B
    NG (for 2KD-FTV)
    C
    NG (for 5L-E)
    D
    NG (for 1GD-FTV)
    E



B
REPLACE FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY (Click here)

C
REPLACE FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY (Click here)

D
REPLACE FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY (Click here)

E
REPLACE FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY (Click here)
A


5. INSPECT FUEL SENDER GAUGE ASSEMBLY

  1. E293045E01
    Remove the fuel sender gauge assembly.
    1. for 1KD-FTV: Click here
    2. for 2KD-FTV: Click here
    3. for 5L-E: Click here
    4. for 1GD-FTV: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    13.5 to 16.5 Ω
    Float level is E (lower)
    405.5 to 414.5 Ω

    Text in Illustration  
    *a
    F (Upper)
    *b
    E (Lower)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1KD-FTV)
    B
    NG (for 2KD-FTV)
    C
    NG (for 5L-E)
    D
    NG (for 1GD-FTV)
    E



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

E
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

6. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY)
  1. Disconnect the H20 combination meter assembly connector.

  1. Disconnect the h2 front fuel main and return tube sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H20-33 (FUEL) - h2-2
    Always
    Below 1 Ω
    H20-34 (E2) - h2-3
    H20-33 (FUEL) or h2-2 - Body ground
    Always
    10 kΩ or higher
    H20-34 (E2) or h2-3 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

  1. E158805E11
    Remove the front fuel main and return tube sub-assembly.
    1. for 1TR-FE: Click here
    2. for 2TR-FE: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-2
    Always
    Below 1 Ω
    A-3 - B-1

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1TR-FE)
    B
    NG (for 2TR-FE)
    C



B
REPLACE FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY (Click here)

C
REPLACE FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY (Click here)
A


8. INSPECT FUEL SENDER GAUGE ASSEMBLY

  1. E293045E01
    Remove the fuel sender gauge assembly.
    1. for 1TR-FE: Click here
    2. for 2TR-FE: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    13.5 to 16.5 Ω
    Float level is E (lower)
    405.5 to 414.5 Ω

    Text in Illustration  
    *a
    F (Upper)
    *b
    E (Lower)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1TR-FE)
    B
    NG (for 2TR-FE)
    C



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Fuel Receiver Gauge Malfunction (Jan 2015 – Dec 2016)Engine Coolant Temperature Receiver Gauge Malfunction (Oct 2014 – Dec 2014) →