C0210/33 Rear Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Also covers:
- C0215/34 Rear Speed Sensor LH Circuit
- C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH
- C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH
- C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
Refer to DTCs C0200/31, C0205/32, C1235/35, and C1236/36 (Click here).DTCs C1273/73 to C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1273/73 to C1278/78 are output only in the Test Mode.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C0210/33 C0215/34 |
With vehicle speed at 6 mph (10 km/h) or more, sensor signal circuit of faulty wheel is open or short for 1 second or more.
|
|
| C1238/38 C1239/39 |
At vehicle speed of 12 mph (20 km/h) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more. |
|
- HINT:
- DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
- DTC C0215/34 and C1239/39 are for the rear speed sensor LH.
- DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Start the inspection from step 1 when using the intelligent tester and start from step 3 when not using the intelligent tester.
| 1. READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION OF REAR SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the intelligent tester main switch on.
Select the DATA LIST mode on the intelligent tester.
ABS: Item (Display)
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
RR Speed Open
Speed sensor open detection
(RR) / OPN DET or NORMAL
OPN DET: Momentary interruption
NORMAL: Normal
-
RL Speed Open
Speed sensor open detection
(RL) / OPN DET or NORMAL
OPN DET: Momentary interruption
NORMAL: Normal
-
Check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).
- OK:
- There are no momentary interruptions.
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Select the DATA LIST mode on the intelligent tester.
ABS: Item (Display)
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
RR Wheel Speed
Wheel speed sensor (RR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h)
Actual wheel speed
Similar speed as indicated on speedometer
RL Wheel Speed
Wheel speed sensor (RL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h)
Actual wheel speed
Similar speed as indicated on speedometer
Check that there is the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer are almost the same when driving the vehicle.
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.
|
|
||||
| OK | |
| 3. PERFORM TEST MODE (SIGNAL CHECK) |
Clear the DTC (Click here).
Perform sensor signal check in TEST MODE PROCEDURE (Click here).
- OK:
- All Test Mode DTCs are erased.
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 4. INSPECT REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.

Check the speed sensor installation.
- OK:
- The installation nut is tightened properly.
- There is no clearance between the sensor and the rear axle.
- Torque:
- 8.5 N*m (87 kgf*cm, 75 in.*lbf)
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 5. INSPECT SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the sensor tip.
- OK:
- No scratches or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
|
|
||||
| OK | |
| 6. INSPECT REAR SPEED SENSOR |
Install the rear speed sensor.

Disconnect the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Rear speed sensor RH: Tester Connection
Specified Condition
"P1"-4 (RR+) - "P1"-3 (RR-)
1.2+-0.2 kΩ at 25+-5°C
"P1"-4 (RR+) - Body ground
10 kΩ or higher
"P1"-3 (RR-) - Body ground
10 kΩ or higher
"P1"-2 (RL+) - "A"-1 (+)
Below 1 Ω
"P1"-2 (RL+) - "A"-3 (-)
10 kΩ or higher
"P1"-2 (RL+) - Body ground
10 kΩ or higher
"P1"-1 (RL-) - "A"-3 (-)
Below 1 Ω
"P1"-1 (RL-) - "A"-1 (+)
10 kΩ or higher
"P1"-1 (RL-) - Body ground
10 kΩ or higher
Rear speed sensor LH: Tester Connection
Specified Condition
1 (+) - 3 (-)
1.2+-0.2 kΩ at 25+-5°C
1 (+) - Body ground
10 kΩ or higher
3 (-) - Body ground
10 kΩ or higher
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (BETWEEN SKID CONTROL ECU AND REAR SPEED SENSOR) |
Disconnect the skid control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
RH: Tester Connection
Specified Condition
B19-33 (RR+) - P1-4 (RR+)
Below 1 Ω
B19-33 (RR+) - Body ground
10 kΩ or higher
B19-34 (RR-) - P1-3 (RR-)
Below 1 Ω
B19-34 (RR-) - Body ground
10 kΩ or higher
LH: Tester Connection
Specified Condition
B19-11 (RL+) - P1-2 (RL+)
Below 1 Ω
B19-11 (RL+) - Body ground
10 kΩ or higher
B19-12 (RL-) - P1-1 (RL-)
Below 1 Ω
B19-12 (RL-) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 8. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS |
Connect the oscilloscope to terminals RR+ - RR- or RL+ - RL- of the skid control ECU.

Drive the vehicle at about 19 mph (30 km/h), and check the signal waveform.
- OK:
- A waveform as shown in the figure should be output.
- HINT:
- As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the fluctuation in the output voltage becomes greater.
- When noise is identified in the waveform on the oscilloscope, error signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.
- As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the fluctuation in the output voltage becomes greater.
|
|
||||
| OK | |
| 9. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 20 mph (32 km/h) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTCs (C0210/33, C0215/34, C1238/38 and C1239/39) are output
A
DTCs (C0210/33, C0215/34, C1238/38 and C1239/39) are not output (When troubleshooting in accordance with the DTC CHART)
B
DTCs (C0210/33, C0215/34, C1238/38 and C1239/39) are not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
C
|
|
||||
|
|
||||
| A | |
| 10. INSPECT REAR SKID CONTROL ROTOR |
Turn the ignition switch off.
Remove the rear axle shaft (Click here).
Check the rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
|
|
||||
| OK | ||
| ||
