C0210/33 Rear Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built Jan 2015 – Dec 2016
Also covers:
- C0215/34 Rear Speed Sensor LH Circuit
- C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH
- C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH
- C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
Refer to DTCs C0200/31, C0205/32, C1235/35, and C1236/36 (Click here).DTCs C1273/73 to C1278/78 can be cleared when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1273/73 to C1278/78 are output only in the Test Mode.
- HINT:
- When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


| *1 |
Rear Speed Sensor |
*2 |
Rear Skid Control Rotor |
| *a |
Waveform (Reference): Between Speed Sensor (-) and Body Ground |
*b |
Low speed |
| *c |
High speed |
- |
- |
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C0210/33 C0215/34 |
|
|
| C1238/38 C1239/39 |
With the vehicle speed 20 km/h (12 mph) or higher, noise is detected 75 times in the speed sensor signal within 5 seconds. |
|
| C1273/73 C1274/74 |
Detected only during Test Mode. |
|
| C1277/77 C1278/78 |
Detected only during Test Mode. |
|
- HINT:
- DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
- DTC C0215/34 and C1239/39 are for the rear speed sensor LH.
- DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION OF REAR SPEED SENSOR) |
Using a GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Speed Open
Rear speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Open
Rear speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
- OK:
- Normal (There are no momentary interruptions.)
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Select the DATA LIST mode on the GTS.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Rear wheel speed sensor RH reading / min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RL Wheel Speed
Rear wheel speed sensor LH reading / min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Check that the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer are almost the same when driving the vehicle.
- OK:
- The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed.
|
|
||||
| OK | |
| 3. PERFORM TEST MODE (SIGNAL CHECK) |
Perform sensor signal check in TEST MODE PROCEDURE (Click here).
- OK:
- All Test Mode DTCs are cleared.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 5. INSPECT REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation (Click here).

- OK:
- There is no clearance between the sensor and the rear axle housing.
- The installation nut is tightened properly.
Text in Illustration *a
Normal
*b
Abnormal
*c
Clearance
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 6. INSPECT SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the sensor tip.
- OK:
- No scratches or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
- If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
- Check the speed sensor signal after cleaning or replacement (Click here).
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 7. INSPECT REAR SKID CONTROL ROTOR |
Remove the rear axle shaft with backing plate (Click here).
Check the rear skid control rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
Reinstall the rear speed sensor and the rear axle shaft with backing plate (Click here for speed sensor, Click here for rear axle shaft with backing plate).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the B19 skid control ECU (brake actuator assembly) connector and the P1 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
B19-33 (RR+) - P1-4 (RR+)
Always
Below 1 Ω
B19-33 (RR+) or P1-4 (RR+) - Body ground
Always
10 kΩ or higher
B19-34 (RR-) - P1-3 (RR-)
Always
Below 1 Ω
B19-34 (RR-) or P1-3 (RR-) - Body ground
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
B19-11 (RL+) - P1-2 (RL+)
Always
Below 1 Ω
B19-11 (RL+) or P1-2 (RL+) - Body ground
Always
10 kΩ or higher
B19-12 (RL-) - P1-1 (RL-)
Always
Below 1 Ω
B19-12 (RL-) or P1-1 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. INSPECT REAR SPEED SENSOR RH |
Turn the ignition switch off.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A rear speed sensor RH connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-3 - P1-1 (RL-)
Always
Below 1 Ω
A-3 or P1-1 (RL-) - Body ground
Always
10 kΩ or higher
A-1 - P1-2 (RL+)
Always
Below 1 Ω
A-1 or P1-2 (RL+) - Body ground
Always
10 kΩ or higher
Text in Illustration *1
Rear Speed Sensor RH
*a
Front view of wire harness connector
(to Sensor Side Connector)
*b
Front view of wire harness connector
(to Vehicle Side Connector)
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 10. INSPECT BRAKE ACTUATOR ASSEMBLY |
Reconnect the B19 skid control ECU (brake actuator assembly) connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for RH Tester Connection
Switch Condition
Specified Condition
P1-4 (RR+) - Body ground
Ignition switch ON
5.7 to 14 V
for LH Tester Connection
Switch Condition
Specified Condition
P1-2 (RL+) - Body ground
Ignition switch ON
5.7 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Rear Speed Sensor RH)
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 11. RECONFIRM DTC |
Reconnect the A and P1 rear speed sensor RH connectors.
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 12. REPLACE REAR SPEED SENSOR |
Replace the rear speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 13. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 14. REPLACE REAR SKID CONTROL ROTOR |
Replace the rear skid control rotor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 15. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
