2014-2019 Hiace · Service Manual BRAKE

C0210/33 Rear Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

Refer to DTCs C0200/31, C0205/32, C1235/35, and C1236/36 (Click here).
DTCs C1273/73 to C1278/78 can be cleared when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1273/73 to C1278/78 are output only in the Test Mode.

HINT:
When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.

C321041E02
Text in Illustration 
*1
Rear Speed Sensor
*2
Rear Skid Control Rotor
*a
Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b
Low speed
*c
High speed
-
-
DTC No.
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
  1. With the vehicle speed 10 km/h (6 mph) or higher, an open or short circuit in the speed sensor signal circuit continuously occurs for 15 seconds or more.
  2. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  3. From when the ignition switch is turned to ON until it is turned off, a speed sensor momentary open circuit signal occurs 255 times or more.
  1. Rear speed sensor RH/LH
  2. Rear speed sensor RH/LH circuit
  3. Skid control rotor
  4. Sensor installation
  5. Skid control ECU (brake actuator assembly)
C1238/38
C1239/39
With the vehicle speed 20 km/h (12 mph) or higher, noise is detected 75 times in the speed sensor signal within 5 seconds.
  1. Rear speed sensor RH/LH
  2. Skid control rotor
  3. Sensor installation
  4. Skid control ECU (brake actuator assembly)
C1273/73
C1274/74
Detected only during Test Mode.
  1. Rear speed sensor RH/LH
  2. Skid control rotor
  3. Sensor installation
C1277/77
C1278/78
Detected only during Test Mode.
  1. Rear speed sensor RH/LH
  2. Skid control rotor

HINT:
  1. DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
  2. DTC C0215/34 and C1239/39 are for the rear speed sensor LH.


WIRING DIAGRAM

C321038E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION OF REAR SPEED SENSOR)
  1. Using a GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    Rear speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RL Speed Open
    Rear speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption

OK:
Normal (There are no momentary interruptions.)

HINT:
Perform the above inspection before removing the sensor and connector.



NG
Go to step 8
OK


2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Select the DATA LIST mode on the GTS.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear wheel speed sensor RH reading / min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check that the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer are almost the same when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed.



NG
Go to step 5
OK


3. PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform sensor signal check in TEST MODE PROCEDURE (Click here).

    OK:
    All Test Mode DTCs are cleared.



NG
Go to step 5
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
Go to step 12
A

USE SIMULATION METHOD TO CHECK (Click here)

5. INSPECT REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C100381E01
    Check the speed sensor installation (Click here).

    OK:
    There is no clearance between the sensor and the rear axle housing.
    The installation nut is tightened properly.

    Text in Illustration 
    *a
    Normal
    *b
    Abnormal
    *c
    Clearance

NOTICE:
Check the speed sensor signal after replacement (Click here).



NG
INSTALL REAR SPEED SENSOR CORRECTLY OR REPLACE REAR SPEED SENSOR
OK


6. INSPECT SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    1. If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
    3. Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


7. INSPECT REAR SKID CONTROL ROTOR
  1. Remove the rear axle shaft with backing plate (Click here).

  1. Check the rear skid control rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

  1. Reinstall the rear speed sensor and the rear axle shaft with backing plate (Click here for speed sensor, Click here for rear axle shaft with backing plate).



NG
CLEAN OR REPLACE REAR SKID CONTROL ROTOR
OK


8. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the B19 skid control ECU (brake actuator assembly) connector and the P1 rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    B19-33 (RR+) - P1-4 (RR+)
    Always
    Below 1 Ω
    B19-33 (RR+) or P1-4 (RR+) - Body ground
    Always
    10 kΩ or higher
    B19-34 (RR-) - P1-3 (RR-)
    Always
    Below 1 Ω
    B19-34 (RR-) or P1-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    B19-11 (RL+) - P1-2 (RL+)
    Always
    Below 1 Ω
    B19-11 (RL+) or P1-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    B19-12 (RL-) - P1-1 (RL-)
    Always
    Below 1 Ω
    B19-12 (RL-) or P1-1 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT REAR SPEED SENSOR RH

  1. C319887E01
    Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the A rear speed sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - P1-1 (RL-)
    Always
    Below 1 Ω
    A-3 or P1-1 (RL-) - Body ground
    Always
    10 kΩ or higher
    A-1 - P1-2 (RL+)
    Always
    Below 1 Ω
    A-1 or P1-2 (RL+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear Speed Sensor RH
    *a
    Front view of wire harness connector
    (to Sensor Side Connector)
    *b
    Front view of wire harness connector
    (to Vehicle Side Connector)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE REAR SPEED SENSOR RH (Click here)
OK


10. INSPECT BRAKE ACTUATOR ASSEMBLY

  1. C321142E01
    Reconnect the B19 skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    P1-4 (RR+) - Body ground
    Ignition switch ON
    5.7 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    P1-2 (RL+) - Body ground
    Ignition switch ON
    5.7 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Speed Sensor RH)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


11. RECONFIRM DTC
  1. Reconnect the A and P1 rear speed sensor RH connectors.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 12
A

USE SIMULATION METHOD TO CHECK (Click here)

12. REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


13. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 14
A

END

14. REPLACE REAR SKID CONTROL ROTOR
  1. Replace the rear skid control rotor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


15. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END


← C0210/33 Rear Speed Sensor RH Circuit (+ 7 more codes) (Jan 2015 – Dec 2016)C0226/21 SFR Solenoid Circuit (+ C0236/22, C0246/23) (Oct 2014 – Dec 2014) →