Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2019.02–2019.06
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0386559 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 82121 2.REMOVE ENGINE WIRE

Hide 26100G 3.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 89481B 5.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 6.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 12631A 10.REMOVE ENGINE COVER BRACKET

a.
A343495

Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


Hide 16206B 15.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 16206B 16.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.
A368227

Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


b.
A446618C01
0.083,0.104 0.323,0.281 0.24,0.177 10 true *A 0.115,2.667 0.344,2.844 0.229,0.177 10 true *B
*A w/ EGR System
*B w/o EGR System


w/ EGR System:

i.

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


ii.

Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.



c.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the EGR valve adapter sub-assembly.


Hide 27148A 17.REMOVE CONNECTING WIRE

a.
A343587

Disconnect the connector from the common rail assembly.


b.

Detach the 2 clamps and remove the connecting wire from the hose bracket.


Hide 25601 18.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

a.
A343497

Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25601 19.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)

a.
A443340

Slide the 2 clamps and remove the water hose from the EGR pipe with cooler sub-assembly and No. 5 water by-pass pipe.


b.
A442600

Remove the bolt and disconnect the No. 1 EGR pipe with cooler sub-assembly from the cylinder head sub-assembly.


c.
A442601

Remove the 4 nuts and No. 1 EGR pipe with cooler sub-assembly from the exhaust manifold and EGR valve adapter.


d.

Remove the 2 gaskets.


e.
A442602

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25804 20.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 16209 21.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A354082C01
0.969,0.24 1.177,0.24 1.177,0.24 1.74,0.781 true 0.781,2 0.99,2 0.99,2 1.396,1.583 true 3.031,2.063 2.802,2.063 2.802,2.063 2.802,1.781 true 2.167,0.125 2.354,0.125 2.354,0.125 2.698,0.458 true 2.188,2.594 2.375,2.594 2.375,2.594 2.635,3.021 true 1.042,3.333 1.74,3.333 true 3.052,3.667 2.823,3.667 2.823,3.667 2.823,4.167 true 0.104,0.063 0.469,0.313 0.365,0.25 12 false *A 0.104,2.49 0.5,2.74 0.396,0.25 12 false *B 3.073,3.573 3.333,3.792 0.26,0.219 10 true *1 0.802,0.135 1.042,0.333 0.24,0.198 10 true *2 1.969,0.031 2.177,0.229 0.208,0.198 10 true *3 0.625,1.906 0.938,2.063 0.313,0.156 10 false *4 3.063,1.979 3.313,2.198 0.25,0.219 10 true *1 2.01,2.5 2.271,2.719 0.26,0.219 10 true *3 0.865,3.24 1.104,3.438 0.24,0.198 10 true *2
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 11 Water By-pass Hose


Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


b.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


c.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


d.

for Cold Area Specification Vehicles:

Detach the clamp and disconnect the No. 11 water by-pass hose from the diesel throttle body assembly.


e.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.


Hide 25800 22.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 23.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

a.
A365517

Remove the 4 bolts and EGR valve adapter sub-assembly with electric EGR control valve assembly from the intake manifold.


Hide 25624 24.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY (w/o EGR System)

a.
A398418

Remove the 4 bolts and EGR valve adapter sub-assembly from the intake manifold.


Hide 25617 25.REMOVE EGR HOLE COVER PLATE (w/o EGR System)

a.
A398420

Remove the 4 nuts, 2 EGR hole plates and 2 gaskets from the intake manifold and exhaust manifold.


b.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 11409 26.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23812D 27.REMOVE NO. 2 FUEL PIPE

a.
A343499

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


b.

Remove the bolt and No. 2 fuel pipe from the manifold stay.


Hide 28.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 30.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 31.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 32.REMOVE NO. 2 FUEL HOSE

Hide 23271H 33.REMOVE NO. 1 FUEL HOSE

Hide 23804D 34.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23804D 35.REMOVE NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23815D 36.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 37.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 38.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 40.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 42.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 43.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A343500

Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.


Hide 23701 44.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 45.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 46.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 19850 47.REMOVE GLOW PLUG ASSEMBLY

Hide 44781 48.REMOVE HOSE BRACKET

a.
A343501

Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.


Hide 23300D 49.REMOVE DIESEL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)

a.
A347297

Remove the 2 nuts and diesel fuel filter assembly from the cylinder block sub-assembly.


Hide 23780B 50.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)

a.
A343502

Remove the 2 nuts and No. 3 nozzle leakage pipe from the cylinder block sub-assembly.


Hide 16025 51.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343503

Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


b.
A443341

for Laminated EGR Pre-cooler:

Remove the 4 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


Hide 88320 52.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 88431 53.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

a.
A343504

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 16632B 54.REMOVE NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)

a.
A347298

Remove the 3 bolts and No. 2 idler pulley bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 89422P 55.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 12229 56.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 16282 57.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.
A347299

Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.


b.

Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.


Hide 16281 58.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.
A347300

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


Hide 23295D 59.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 17167 62.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)

a.
A443331

Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 17271 64.REMOVE NO. 1 TURBO INSULATOR (w/o EGR Cooler)

a.
A443332

Remove the 3 bolts and No. 1 turbo insulator from the turbine outlet elbow and turbocharger sub-assembly.


Hide 66.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)

a.
A443333

Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and turbine outlet elbow.


Hide 68.REMOVE EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)

a.
A443334

Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and turbine outlet elbow.


Hide 25051 69.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)

Hide 17291 70.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)

a.
A443335

Remove the nut, exhaust pipe clamp and turbine outlet elbow from the turbocharger sub-assembly.


b.

Remove the gasket.


Hide 12261 71.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 73.REMOVE WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)

Hide 16268 74.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A347301C03
0.115,0.146 0.427,0.302 0.313,0.156 10 false *A 0.146,2.479 0.458,2.635 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.


b.
A444765C01
0.115,0.125 0.427,0.281 0.313,0.156 10 false *A 0.146,2.552 0.458,2.708 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


for Water Cooled Compressor Housing Turbocharger:

Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.


Hide 16284 75.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 76.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.
A347302

Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly from the cylinder block sub-assembly and timing chain cover sub-assembly.


Hide 15407 79.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 83530 82.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 16207 83.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343506

Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.


b.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


Hide 16304 84.REMOVE WATER OUTLET SUB-ASSEMBLY

a.

Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.

A444766C01
0.25,0.333 0.563,0.49 0.313,0.156 10 false *A 2.521,0.333 2.833,0.49 0.313,0.156 10 false *B 4.906,0.323 5.219,0.479 0.313,0.156 10 false *C
*A w/ DPF *B w/o DPF
*C w/o EGR System - -



b.

Remove the gasket from the timing chain cover sub-assembly.


Hide 16321 85.REMOVE WATER INLET

a.
A343508

Remove the 3 bolts and water inlet from the timing chain cover sub-assembly.


Hide 16331A 86.REMOVE THERMOSTAT

Hide 16603 87.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 88.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 25706 89.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A365406C02
0.135,0.115 0.479,0.375 0.344,0.26 12 false *A 0.135,2.417 0.438,2.698 0.302,0.281 12 false *B
*A w/ EGR System with EGR Cooler
*B w/ EGR System without EGR Cooler


w/ EGR System with EGR Cooler:

Disconnect the No. 1 vacuum transmitting hose from the vacuum pump assembly.


b.

Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.


Hide 29300 90.REMOVE VACUUM PUMP ASSEMBLY

a.
A343510

Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.


b.

Remove the 2 O-rings from the vacuum pump assembly.


Hide 11382C 91.REMOVE CAMSHAFT OIL SEAL RETAINER

a.
A343511

Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 88451B 92.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 13496 93.REMOVE CRANKSHAFT PULLY COVER (for Automatic Transmission)

Hide 13407 94.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)

Hide 13471 95.REMOVE CRANKSHAFT PULLEY (for Automatic Transmission)

Hide 16575C 96.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.
A347304

Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.