Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388652 ECD SYSTEM(w/o EGR Cooler) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A206916E82
4.375,1.25 6.219,1.594 1.844,0.344 10 false 5 V Constant Voltage Circuit 5.354,2.094 6.365,2.438 1.01,0.344 10 false Microprocessor 1.323,1.146 2.75,1.417 1.427,0.271 10 false from EFI-MAIN Fuse 1.302,1.469 3.25,1.75 1.948,0.281 10 false from EFI MAIN Relay 2.906,1.031 3.302,1.219 0.396,0.188 10 false BATT 0.354,2.229 2.615,2.802 2.26,0.573 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (sensors which have ICs) 0.365,2.969 2.625,3.438 2.26,0.469 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.063,3.125 4.323,3.333 0.26,0.208 10 false R 3,1.375 3.281,1.573 0.281,0.198 10 false +B 3.177,2.25 3.542,2.479 0.365,0.229 10 false VC 4.885,3.375 5.333,3.604 0.448,0.229 10 false ECM

When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source circuit.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>ECM Power Source Circuit

·

VC Power Source Circuit


A348659E19
5.875,8.427 6.26,8.604 0.385,0.177 10 false ECM 5.198,0.5 5.51,0.656 0.313,0.156 10 false A2 5.198,0.875 5.51,1.031 0.313,0.156 10 false A2 5.208,1.24 5.521,1.396 0.313,0.156 10 false A2 5.198,1.615 5.51,1.771 0.313,0.156 10 false A2 5.198,1.99 5.51,2.146 0.313,0.156 10 false A2 5.198,2.365 5.51,2.521 0.313,0.156 10 false A2 5.208,3.604 5.5,3.781 0.292,0.177 10 false E8 5.208,4 5.5,4.177 0.292,0.177 10 false E8 5.208,4.396 5.5,4.573 0.292,0.177 10 false E8 5.208,4.781 5.5,4.958 0.292,0.177 10 false E7 5.208,5.177 5.5,5.354 0.292,0.177 10 false E7 5.208,5.563 5.5,5.74 0.292,0.177 10 false E7 5.198,6.865 5.49,7.042 0.292,0.177 10 false E7 5.208,7.26 5.5,7.438 0.292,0.177 10 false E7 5.208,7.656 5.5,7.833 0.292,0.177 10 false E7 0.438,2.708 0.75,2.865 0.313,0.156 10 false M3 0.438,2.854 3.24,3.281 2.802,0.427 10 false Accelerator Pedal Position Sensor (Accelerator Pedal Sensor Assembly) 0.427,5.938 0.885,6.135 0.458,0.198 10 false E105 0.427,6.083 1.813,6.271 1.385,0.188 10 false Fuel Pressure Sensor 0.417,8.135 0.917,8.344 0.5,0.208 10 false E103 0.417,8.302 2.344,8.49 1.927,0.188 10 false Diesel Throttle Body Assembly 2.104,0.375 2.26,0.531 0.156,0.156 10 false 1 2.104,0.75 2.26,0.906 0.156,0.156 10 false 2 2.104,1.115 2.26,1.271 0.156,0.156 10 false 3 2.104,1.49 2.26,1.646 0.156,0.156 10 false 4 2.104,1.865 2.26,2.021 0.156,0.156 10 false 5 2.104,2.24 2.26,2.396 0.156,0.156 10 false 6 2.115,3.479 2.271,3.635 0.156,0.156 10 false 1 2.115,3.875 2.271,4.031 0.156,0.156 10 false 2 2.115,4.26 2.271,4.417 0.156,0.156 10 false 3 2.115,4.656 2.271,4.813 0.156,0.156 10 false 4 2.115,5.052 2.271,5.208 0.156,0.156 10 false 5 2.115,7.135 2.271,7.292 0.156,0.156 10 false 5 2.115,6.74 2.271,6.896 0.156,0.156 10 false 3 2.115,7.531 2.271,7.688 0.156,0.156 10 false 6 5.208,0.323 5.427,0.479 0.219,0.156 10 false 30 5.219,0.698 5.438,0.854 0.219,0.156 10 false 25 2.115,5.438 2.271,5.594 0.156,0.156 10 false 6 5.219,1.073 5.438,1.229 0.219,0.156 10 false 31 5.219,1.438 5.438,1.594 0.219,0.156 10 false 29 5.219,1.813 5.438,1.969 0.219,0.156 10 false 22 5.208,3.427 5.427,3.583 0.219,0.156 10 false 22 5.219,3.823 5.438,3.979 0.219,0.156 10 false 23 5.219,4.219 5.438,4.375 0.219,0.156 10 false 21 5.208,4.604 5.427,4.76 0.219,0.156 10 false 19 5.219,5 5.438,5.156 0.219,0.156 10 false 18 5.229,5.385 5.448,5.542 0.219,0.156 10 false 28 5.219,6.698 5.438,6.854 0.219,0.156 10 false 20 5.219,7.083 5.438,7.24 0.219,0.156 10 false 29 5.219,7.479 5.438,7.635 0.219,0.156 10 false 21 1.625,0.5 2.042,0.667 0.417,0.167 10 false VCP2 5.542,0.51 5.958,0.677 0.417,0.167 10 false VCP2 1.625,0.865 2.042,1.031 0.417,0.167 10 false EPA2 5.542,0.875 5.958,1.042 0.417,0.167 10 false EPA2 1.625,1.24 2.042,1.406 0.417,0.167 10 false VPA2 5.542,1.25 5.958,1.417 0.417,0.167 10 false VPA2 1.604,1.615 2.042,1.781 0.438,0.167 10 false VCPA 5.542,1.615 5.979,1.781 0.438,0.167 10 false VCPA 1.688,1.99 2.042,2.156 0.354,0.167 10 false EPA 5.542,1.99 5.896,2.156 0.354,0.167 10 false EPA 1.688,2.354 2.042,2.521 0.354,0.167 10 false VPA 5.542,2.365 5.896,2.531 0.354,0.167 10 false VPA 5.219,2.188 5.438,2.344 0.219,0.156 10 false 28 1.698,3.594 2.052,3.76 0.354,0.167 10 false VCS 5.542,3.615 5.896,3.781 0.354,0.167 10 false VCS 1.729,3.99 2.052,4.156 0.323,0.167 10 false PR2 5.542,6.865 5.948,7.031 0.406,0.167 10 false EVLU 1.74,4.396 2.052,4.563 0.313,0.167 10 false E2S 5.542,4.396 5.854,4.563 0.313,0.167 10 false E2S 1.823,4.781 2.052,4.948 0.229,0.167 10 false E2 5.542,4.781 5.875,4.948 0.333,0.167 10 false E2M 1.823,5.177 2.052,5.344 0.229,0.167 10 false PR 5.542,5.177 5.948,5.354 0.406,0.177 10 false PCR1 1.823,5.563 2.052,5.729 0.229,0.167 10 false VC 5.542,5.573 5.885,5.74 0.344,0.167 10 false VCM 1.823,6.865 2.052,7.031 0.229,0.167 10 false E2 1.823,7.26 2.052,7.427 0.229,0.167 10 false VC 5.542,7.656 5.854,7.823 0.313,0.167 10 false VLU 5.542,7.26 5.948,7.427 0.406,0.167 10 false VCVL 5.542,3.99 5.948,4.156 0.406,0.167 10 false PCR2 1.74,7.656 2.052,7.823 0.313,0.167 10 false VTA

A383902E05
0.51,2.667 3.021,2.906 2.51,0.24 10 false Electric EGR Control Valve Assembly* 0.49,4.646 0.823,4.833 0.333,0.188 10 false E40 0.49,4.833 3,5.073 2.51,0.24 10 false Manifold Absolute Pressure Sensor 0.51,2.5 0.844,2.688 0.333,0.188 10 false E33 0.49,6.792 1.188,6.99 0.698,0.198 10 false E79 0.49,6.969 3,7.208 2.51,0.24 10 false Camshaft Position Sensor 0.5,8.948 0.833,9.135 0.333,0.188 10 false E42 0.51,9.125 3.021,9.365 2.51,0.24 10 false Nozzle Vane Position Sensor 6.021,9.271 6.479,9.479 0.458,0.208 10 false ECM 1.865,0.677 2.198,0.865 0.333,0.188 10 false E2 1.802,1.052 2.135,1.24 0.333,0.188 10 false VTA 1.865,1.417 2.198,1.604 0.333,0.188 10 false VC 1.875,1.781 2.208,1.969 0.333,0.188 10 false M+ 1.896,2.146 2.229,2.333 0.333,0.188 10 false M- 5.281,0.667 5.615,0.854 0.333,0.188 10 false E7 5.635,0.656 6.146,0.844 0.51,0.188 10 false EEGL* 5.292,0.479 5.625,0.667 0.333,0.188 10 false 24 2.177,0.552 2.51,0.74 0.333,0.188 10 false 1 2.188,0.948 2.521,1.135 0.333,0.188 10 false 2 2.188,1.313 2.521,1.5 0.333,0.188 10 false 3 2.188,1.688 2.521,1.875 0.333,0.188 10 false 4 2.188,2.063 2.521,2.25 0.333,0.188 10 false 5 5.292,0.865 5.625,1.052 0.333,0.188 10 false 25 5.292,1.229 5.625,1.417 0.333,0.188 10 false 31 5.323,1.604 5.656,1.792 0.333,0.188 10 false 6 5.333,1.979 5.667,2.167 0.333,0.188 10 false 7 5.625,1.042 6.135,1.229 0.51,0.188 10 false EGRA* 5.635,1.417 6.146,1.604 0.51,0.188 10 false VCEG* 5.615,1.802 6.125,1.99 0.51,0.188 10 false EGM+* 5.625,2.156 6.135,2.344 0.51,0.188 10 false EGM-* 1.99,3.438 2.323,3.625 0.333,0.188 10 false E 1.854,3.833 2.188,4.021 0.333,0.188 10 false PIM 1.896,4.229 2.229,4.417 0.333,0.188 10 false VC 2.208,3.333 2.542,3.521 0.333,0.188 10 false 1 2.219,3.719 2.552,3.906 0.333,0.188 10 false 2 2.219,4.115 2.552,4.302 0.333,0.188 10 false 3 5.615,3.438 6.125,3.625 0.51,0.188 10 false EPIM 5.281,3.25 5.615,3.438 0.333,0.188 10 false 19 5.292,3.438 5.625,3.625 0.333,0.188 10 false E5 5.281,3.646 5.615,3.833 0.333,0.188 10 false 18 5.292,4.042 5.625,4.229 0.333,0.188 10 false 28 5.625,3.844 6.135,4.031 0.51,0.188 10 false PIM 5.625,4.229 6.135,4.417 0.51,0.188 10 false VCPM 2.219,6.26 2.552,6.448 0.333,0.188 10 false 3 2.219,5.854 2.552,6.042 0.333,0.188 10 false 2 2.208,5.458 2.542,5.646 0.333,0.188 10 false 1 2.219,8.406 2.552,8.594 0.333,0.188 10 false 3 2.208,8.021 2.542,8.208 0.333,0.188 10 false 2 2.198,7.625 2.531,7.813 0.333,0.188 10 false 1 1.75,5.573 2.198,5.76 0.448,0.188 10 false G22+ 1.75,5.979 2.156,6.167 0.406,0.188 10 false G22- 1.906,6.375 2.24,6.563 0.333,0.188 10 false VC 1.708,7.75 2.198,7.958 0.49,0.208 10 false VNVC 1.729,8.125 2.219,8.323 0.49,0.198 10 false VNE2 1.75,8.531 2.208,8.75 0.458,0.219 10 false VTA1 5.635,5.573 6.146,5.76 0.51,0.188 10 false G2+ 5.625,5.979 6.135,6.167 0.51,0.188 10 false G2- 5.635,6.375 6.146,6.563 0.51,0.188 10 false VCG 5.615,7.74 6.125,7.927 0.51,0.188 10 false VNVC 5.625,8.135 6.135,8.323 0.51,0.188 10 false VNE2 5.625,8.531 6.135,8.719 0.51,0.188 10 false VNA 5.292,5.375 5.625,5.563 0.333,0.188 10 false 27 5.292,7.531 5.625,7.719 0.333,0.188 10 false 30 5.302,8.344 5.635,8.531 0.333,0.188 10 false 23 5.292,7.948 5.625,8.135 0.333,0.188 10 false 22 5.292,5.792 5.625,5.979 0.333,0.188 10 false 18 5.281,6.188 5.615,6.375 0.333,0.188 10 false 17 5.281,1.042 5.615,1.229 0.333,0.188 10 false E7 5.281,1.417 5.615,1.604 0.333,0.188 10 false E7 5.281,1.781 5.615,1.969 0.333,0.188 10 false E7 5.281,2.156 5.615,2.344 0.333,0.188 10 false E7 5.292,3.833 5.625,4.021 0.333,0.188 10 false E5 5.292,4.229 5.625,4.417 0.333,0.188 10 false E5 5.292,5.583 5.625,5.771 0.333,0.188 10 false E8 5.292,5.969 5.625,6.156 0.333,0.188 10 false E8 5.292,6.365 5.625,6.552 0.333,0.188 10 false E8 5.292,7.75 5.625,7.938 0.333,0.188 10 false E7 5.292,8.146 5.625,8.333 0.333,0.188 10 false E7 5.292,8.531 5.625,8.719 0.333,0.188 10 false E7 2.938,9.24 5.448,9.479 2.51,0.24 10 false *: w/ EGR System

A445188E01
0.25,7.167 5.75,7.365 5.5,0.198 10 false Clutch Pedal Stroke Sensor Assembly* 0.25,7.021 5.75,7.219 5.5,0.198 10 false M6 3.01,7.427 5.198,7.74 2.188,0.313 10 false *: for Manual Transmission 5.969,7.448 7.156,7.854 1.188,0.406 10 false ECM 1.625,6.521 2.24,6.719 0.615,0.198 10 false SKS1 1.698,6.125 2.313,6.323 0.615,0.198 10 false SKG 1.615,5.729 2.229,5.927 0.615,0.198 10 false VCSK 2.156,5.594 2.771,5.792 0.615,0.198 10 false 3 2.156,5.99 2.771,6.188 0.615,0.198 10 false 1 2.156,6.406 2.771,6.604 0.615,0.198 10 false 2 5.208,5.729 5.823,5.927 0.615,0.198 10 false A2 5.208,6.125 5.823,6.323 0.615,0.198 10 false A2 5.219,6.521 5.833,6.719 0.615,0.198 10 false A2 5.219,5.51 5.833,5.708 0.615,0.198 10 false 23 5.219,5.927 5.833,6.125 0.615,0.198 10 false 21 5.24,6.333 5.854,6.531 0.615,0.198 10 false 20 5.573,5.719 6.188,5.917 0.615,0.198 10 false VCCL* 5.583,6.094 6.198,6.292 0.615,0.198 10 false CLS* 5.594,6.531 6.208,6.729 0.615,0.198 10 false CLS* 0.333,4.823 5.833,5.021 5.5,0.198 10 false Crankshaft Position Sensor 0.333,4.656 5.833,4.854 5.5,0.198 10 false E104 1.74,3.375 7.156,3.573 5.417,0.198 10 false NE+ 1.74,3.76 7.156,3.958 5.417,0.198 10 false NE- 1.74,4.146 7.156,4.344 5.417,0.198 10 false VC 5.229,4.167 7.156,4.448 1.927,0.281 10 false E8 5.229,3.771 7.156,4.052 1.927,0.281 10 false E8 5.229,3.375 7.156,3.656 1.927,0.281 10 false E8 5.573,4.167 7.156,4.448 1.583,0.281 10 false VCNE 5.573,3.771 7.156,4.052 1.583,0.281 10 false NE- 5.573,3.365 7.156,3.646 1.583,0.281 10 false NE+ 2.125,3.646 7.156,3.854 5.031,0.208 10 false 2 2.125,4.042 7.156,4.25 5.031,0.208 10 false 3 5.24,3.177 7.156,3.479 1.917,0.302 10 false 28 2.125,3.24 7.156,3.448 5.031,0.208 10 false 1 5.24,3.583 7.156,3.885 1.917,0.302 10 false 19 5.24,3.99 7.156,4.292 1.917,0.302 10 false 20 5.229,1.896 7.156,2.177 1.927,0.281 10 false E6 5.229,1.521 7.156,1.802 1.927,0.281 10 false E6 5.229,1.146 7.156,1.427 1.927,0.281 10 false E6 5.229,0.781 7.156,1.063 1.927,0.281 10 false E6 5.24,1.719 7.156,2.021 1.917,0.302 10 false 28 5.24,1.344 7.156,1.646 1.917,0.302 10 false 30 5.24,0.969 7.156,1.271 1.917,0.302 10 false 29 5.24,0.594 7.156,0.896 1.917,0.302 10 false 31 0.333,2.354 5.833,2.552 5.5,0.198 10 false E20 0.333,2.521 5.833,2.719 5.5,0.198 10 false Mass Air Flow Meter Sub-assembly 1.74,1.917 7.156,2.115 5.417,0.198 10 false THA 1.74,1.531 7.156,1.729 5.417,0.198 10 false 5V 1.74,1.156 7.156,1.354 5.417,0.198 10 false E2G 1.74,0.792 7.156,0.99 5.417,0.198 10 false FG 5.573,1.917 7.156,2.198 1.583,0.281 10 false THA 5.573,1.521 7.156,1.802 1.583,0.281 10 false VCVG 5.573,1.156 7.156,1.438 1.583,0.281 10 false EVG 5.573,0.792 7.156,1.073 1.583,0.281 10 false VG

CAUTION / NOTICE / HINT

NOTICE:
·

Check the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
A348466C54
2.281,0.365 2.656,0.615 0.375,0.25 1.969,1.698 2.479,1.01 true 2.552,1.698 2.542,1.01 true 3.135,1.74 2.604,1.01 true 2.385,0.417 2.729,0.625 0.344,0.208 10 false N2 2.958,1.771 3.427,1.99 0.469,0.219 10 false 2 (+B) 2.333,1.76 2.854,1.969 0.521,0.208 10 false 3 (+B2) 1.708,1.76 2.229,1.969 0.521,0.208 10 false 4 (+B3) 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Component with harness connected
(to ECM)


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N2-4 (+B) - Body ground Ignition switch ON 11 to 14 V
N2-3 (+B2) - Body ground Ignition switch ON 11 to 14 V
N2-2 (+B3) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is not as specified, since current is not flowing to the +B, +B2 and +B3 terminals of the ECM, the system may not be started.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B



e.

Reconnect the camshaft position sensor connector.



A

B

4.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
4.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B


e.

Reconnect the manifold absolute pressure sensor connector.



A

B

5.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
5.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B


e.

Reconnect the mass air flow meter sub-assembly connector.



A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (NOZZLE VANE POSITION SENSOR)
6.CHECK CONNECTION BETWEEN GTS AND ECM (NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible (w/ EGR System) B
Communication is not possible (w/o EGR System) C


e.

Reconnect the nozzle vane position sensor connector.



A

REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

B

7.CHECK CONNECTION BETWEEN GTS AND ECM (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

C

8.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
7.CHECK CONNECTION BETWEEN GTS AND ECM (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B


e.

Reconnect the electric EGR control valve assembly connector.



A

REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

B

8.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
8.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B


e.

Reconnect the accelerator pedal position sensor connector.



A

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

B

9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)
9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B


e.

Reconnect the fuel pressure sensor connector.



A

REPLACE COMMON RAIL ASSEMBLY

B

10.CHECK CONNECTION BETWEEN GTS AND ECM (DIESEL THROTTLE BODY ASSEMBLY)
10.CHECK CONNECTION BETWEEN GTS AND ECM (DIESEL THROTTLE BODY ASSEMBLY)
a.

Disconnect the diesel throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B


e.

Reconnect the diesel throttle body assembly connector.



A

B

11.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
11.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible (for Manual Transmission) B
Communication is not possible (for Automatic Transmission) C


e.

Reconnect the crankshaft position sensor connector.



A

B

12.CHECK CONNECTION BETWEEN GTS AND ECM (CLUTCH PEDAL STROKE SENSOR ASSEMBLY)

C

13.CHECK HARNESS AND CONNECTOR
12.CHECK CONNECTION BETWEEN GTS AND ECM (CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
a.

Disconnect the clutch pedal stroke sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B


e.

Reconnect the clutch pedal stroke sensor assembly connector.



A

REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

B

13.CHECK HARNESS AND CONNECTOR
13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the manifold absolute pressure sensor connector.


c.

Disconnect the mass air flow meter sub-assembly connector.


d.

Disconnect the nozzle vane position sensor connector.


e.

Disconnect the electric EGR control valve assembly connector (w/ EGR System).


f.

Disconnect the accelerator pedal sensor assembly connector.


g.

Disconnect the fuel pressure sensor connector.


h.

Disconnect the diesel throttle body assembly connector.


i.

Disconnect the crankshaft position sensor connector.


j.

Disconnect the clutch stroke sensor connector (for Manual Transmission).


k.

Disconnect the ECM connectors.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-29 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
A2-30 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
E7-28 (VCM) - Body ground and other terminals Always 10 kΩ or higher
E8-22 (VCS) - Body ground and other terminals Always 10 kΩ or higher
E7-29 (VCVL) - Body ground and other terminals Always 10 kΩ or higher
E7-31 (VCEG)*1 - Body ground and other terminals Always 10 kΩ or higher
E5-28 (VCPM) - Body ground and other terminals Always 10 kΩ or higher
E7-30 (VNVC) - Body ground and other terminals Always 10 kΩ or higher
E6-30 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
E8-17 (VCG) - Body ground and other terminals Always 10 kΩ or higher
E8-20 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
A2-23 (VCCL)*2 - Body ground and other terminals Always 10 kΩ or higher
N2-4 (+B) - Body ground and other terminals Always 10 kΩ or higher
N2-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher
N2-2 (+B3) - Body ground and other terminals Always 10 kΩ or higher


*1: w/ EGR System

*2: for Manual Transmission



m.

Reconnect the clutch stroke sensor connector (for Manual Transmission).


n.

Reconnect the crankshaft position sensor connector.


o.

Reconnect the diesel throttle body assembly connector.


p.

Reconnect the fuel pressure sensor connector.


q.

Reconnect the accelerator pedal sensor assembly connector.


r.

Reconnect the electric EGR control valve assembly connector (w/ EGR System).


s.

Reconnect the nozzle vane position sensor connector.


t.

Reconnect the mass air flow meter sub-assembly connector.


u.

Reconnect the manifold absolute pressure sensor connector.


v.

Reconnect the camshaft position sensor connector.


w.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR